曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

Note: Reverse thrust and speedbrake drag are most effective during the high
speed portion of the landing. Deploy the speedbrake lever and activate
reverse thrust with as little time delay as possible.
Note: Speedbrakes fully deployed, in conjunction with maximum reverse thrust
and maximum manual anti-skid braking provides the minimum stopping
distance.
Floating above the runway before touchdown must be avoided because it uses a large portion of the available runway. The airplane should be landed as near the normal touchdown point as possible. Deceleration rate on the runway is approximately three times greater than in the air.
Height of the airplane over the runway threshold also has a significant effect on total landing distance. For example, on a 3° glide path, passing over the runway threshold at 100 feet altitude rather than 50 feet could increase the total landing distance by approximately 950 feet. This is due to the length of runway used up before the airplane actually touches down.

Glide path angle also affects total landing distance. As the approach path becomes flatter, even while maintaining proper height over the end of the runway, total landing distance is increased.
Slippery Runway Landing Performance
When landing on slippery runways contaminated with ice, snow, slush or standing water, the reported braking action must be considered. Advisory information for reported braking actions of good, medium and poor is contained in the PI section of the QRH. The performance level associated with good is representative of a wet
runway. The performance level associated with poor is representative of a wet ice covered runway. Also provided in the QRH are stopping distances for the various autobrake settings and for non-normal configurations. Pilots should use extreme caution to ensure adequate runway length is available when poor braking action is reported.
Pilots should keep in mind slippery/contaminated runway advisory information is based on an assumption of uniform conditions over the entire runway. This means a uniform depth for slush/standing water for a contaminated runway or a fixed braking coefficient for a slippery runway. The data cannot cover all possible slippery/contaminated runway combinations and does not consider factors such as rubber deposits or heavily painted surfaces near the end of most runways. With these caveats in mind, it is up to the airline to determine operating policies based on the training and operating experience of their flight crews.
One of the commonly used runway descriptors is coefficient of friction. Ground friction measuring vehicles typically measure this coefficient of friction. Much work has been done in the aviation industry to correlate the friction reading from these ground friction measuring vehicles to airplane performance. Use of ground friction vehicles raises the following concerns:
. 
the measured coefficient of friction depends on the type of ground friction
measuring vehicle used. There is not a method, accepted worldwide, for
correlating the friction measurements from the different friction
measuring vehicles to each other, or to the airplane's braking capability.

. 
most testing to date, which compares ground friction vehicle performance
to airplane performance, has been done at relatively low speeds (100
knots or less). The critical part of the airplane's deceleration
characteristics is typically at higher speeds (120 to 150 knots).

 

Copyright . The Boeing Company. See title page for details.
October 31, 2003 FCT 757 (TM) 6.21

. 
ground friction vehicles often provide unreliable readings when
measurements are taken with standing water, slush or snow on the
runway. Ground friction vehicles might not hydroplane (aquaplane) when
taking a measurement while the airplane may hydroplane (aquaplane). In
this case, the ground friction vehicles would provide an optimistic reading
of the runway's friction capability. The other possibility is the ground
friction vehicles might hydroplane (aquaplane) when the airplane would
not, this would provide an overly pessimistic reading of the runway's
friction capability. Accordingly, friction readings from the ground friction
vehicles may not be representative of the airplane's capability in
hydroplaning conditions.

. 
ground friction vehicles measure the friction of the runway at a specific
time and location. The actual runway coefficient of friction may change
with changing atmospheric conditions such as temperature variations,
precipitation etc. Also, the runway condition changes as more operations
are performed.

 

The friction readings from ground friction measuring vehicles do supply an additional piece of information for the pilot to evaluate when considering runway conditions for landing. Crews should evaluate these readings in conjunction with the PIREPS (pilot reports) and the physical description of the runway (snow, slush, ice etc.) when planning the landing. Special care should be taken in evaluating all the information available when braking action is reported as POOR or if slush/standing water is present on the runway.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：757 Flight Crew Training Manual 機組訓練手冊(71)