-------------------------------------------------------------------------------ACTION RESULT -------------------------------------------------------------------------------
-the green MAN indication changes to the green SYS 1 (or SYS 2) indication.
 4. On the CABIN PRESS panel 25VU: On the ECAM upper display unit:
 -move the LDG ELEV selector  - the green MAN LDG ELEV memo message counterclockwise to the AUTO goes off. position.
 On the ECAM lower display unit:
 -the green MAN xxx FT indication changes to the green AUTO xxx FT indication..
 5. Close-up
________
 Subtask 21-31-00-860-056
 A. Aircraft Maintenance Configuration
 (1) Do the EIS stop procedure
 (Ref. TASK 31-60-00-860-002). R
R (2) De-energize the aircraft electrical circuits (Ref. TASK 24-41-00-862-002).

 TASK 21-31-00-710-004 Operational Test of the Outflow Valve Closing in Ditching Configuration WARNING : MAKE SURE THAT AIR IS NOT SUPPLIED TO THE AIR CONDITIONING SYSTEM
_______
 FROM THE MAIN ENGINE, THE APU OR A GROUND SOURCE.
 HOT COMPRESSED AIR CAN CAUSE INJURY TO PERSONNEL.

 WARNING : MAKE SURE THAT THE FWD AVIONICS ACCESS DOOR 811 IS OPEN. WITH A
_______ WARNING PLACARD ATTACHED TO IT. THE WARNING NOTICE MUST TELL PERSONS NOT TO CLOSE THE DOOR. THIS PREVENTS ACCIDENTAL PRESSURIZATION OF THE AIRCRAFT.
 1.
 Reason for the Job

__________________
 Refer to the MPD TASK: 213100-03

 2.
 Job Set-up Information

______________________ R A. Fixtures, Tools, Test and Support Equipment R -------------------------------------------------------------------------------
R REFERENCE QTY DESIGNATION R -------------------------------------------------------------------------------R No specific circuit breaker(s) safety clip(s)
R B. Referenced Information -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------

R  21-31-00-100-001 24-41-00-861-002
24-41-00-862-002
31-60-00-860-001 31-60-00-860-002
3. Job Set-up
__________ Cleaning of the Moveable Seals of the Outflow-ValveEnergize the Aircraft Electrical Circuits from the External PowerDe-energize the Aircraft Electrical Circuits Supplied from the External PowerEIS Start ProcedureEIS Stop Procedure
R  Subtask 21-31-00-861-064
R A. Energize the aircraft electrical circuits R (Ref. TASK 24-41-00-861-002).

 Subtask 21-31-00-865-067
 B. Open, safety and tag this(these) circuit breaker(s):
 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU AIR COND/CAB/PRESS/CTL1 1HL D09 122VU AIR COND/CAB PRESS/CTL/MAN 3HL Y23 122VU AIR COND/CAB PRESS/CTL/2 2HL Y22
 Subtask 21-31-00-860-068
 C. Outflow Valve Seals Inspection
 (1) Do a check of the outflow valve moveable seals installed in the outflow valve gates: - they must move freely with a light finger pressure. - you must clean the seals if they do not move freely (Ref. TASK 21-31-00-100-001).
 Subtask 21-31-00-865-054
 D. Make sure that this(these) circuit breaker(s) is(are) closed:
 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU AIR COND/CAB/PRESS/CTL1 1HL D09 122VU AIR COND/CAB PRESS/CTL/MAN 3HL Y23 122VU AIR COND/CAB PRESS/CTL/2 2HL Y22
 Subtask 21-31-00-860-057 
R R  E. Aircraft Maintenance Configuration 
R  (1) Do the EIS start procedure (Upper ECAM DU and lower ECAM DU only) (Ref. TASK 31-60-00-860-001). 
R R R  (2) Make sure that on the CABIN PRESS section of the panel 25VU: - the MODE SEL pushbutton switch is in the AUTO position (the FAULT and the MAN legends are off).
 NOTE : Make sure there are no persons near the outflow valve before____ you start this test.

 4. Procedure
_________ Subtask 21-31-00-710-054
 A. Operational Test of the Outflow Valve Closing in Ditching Configuration WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE OUTFLOW VALVES ARE
_______ CLEAR. MOVEMENT OF THE OUTFLOW VALVES CAN CAUSE INJURY TO PERSONS AND/OR DAMAGE TO EQUIPMENT.
 WARNING : KEEP AWAY FROM THE MOVING AND ENERGIZED PARTS OF THE OUTFLOW
_______ VALVE WHEN YOU OPERATE OR TEST THE VALVE. THESE CAN CAUSE INJURY TO PERSONS.
 -------------------------------------------------------------------------------ACTION RESULT -------------------------------------------------------------------------------
　
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM AIR CONDITIONING 空調(diào) 3(13)