C. In-Service Wear Limits
(1) Use applicable measurement equipment and measure the outside diameter (OD) of the bolts (5) and the inside diameter (ID) of the bushings (6).
-------------------------------------------------------------------------------| FIG. | ORIGINAL MANUFACTURING LIMITS | IN-SERVICE WEAR LIMITS | | DETAIL |---------------------------------------|----------------------------| | AND | DIMENSION | ASSEMBLY CLEARANCE| DIMENSION LIMITS | MAX. | | ITEM | MM (IN.) | MM (IN.) | MM (IN.) | ALLOW. | | NO. |-------------------|-------------------|---------|---------| CLEAR. | | | MIN. | MAX. | MIN. | MAX. | MIN. | MAX. |MM (IN.)| |--------|---------|---------|---------|---------|---------|---------|--------| | BB | 6.325 | 6.335 | | | 6.318 | | | | OD 5 |(0.2490) |(0.2494) | | |(0.2487) | | | | | | | 0.015 | 0.040 | | | 0.039 | | | | | (0.0005)| (0.0015)| | |(0.0015)| | BB | 6.350 | 6.365 | | | | 6.357 | | | ID 6 |(0.2500) |(0.2505) | | | |(0.2502) | | -------------------------------------------------------------------------------
Subtask 21-51-41-220-053
D. In-Service Wear Limits
(1) Use applicable measurement equipment and measure the outside diameter (OD) of the bolts (5) and the inside diameter (ID) of the shouldered bushings (3).
NOTE : If any of the components are 'out of limits' then you must
____
replace them.
-for item (3) (Ref. TASK 21-51-00-300-001).
R 1EFF : 001-049, 101-105, 151-199, 1 21-51-41Page 604 1 1 May 01/05 1 1 1CES 1 -------------------------------------------------------------------------------| FIG. | ORIGINAL MANUFACTURING LIMITS | IN-SERVICE WEAR LIMITS | | DETAIL |---------------------------------------|----------------------------| | AND | DIMENSION | ASSEMBLY CLEARANCE| DIMENSION LIMITS | MAX. | | ITEM | MM (IN.) | MM (IN.) | MM (IN.) | ALLOW. | | NO. |-------------------|-------------------|---------|---------| CLEAR. | | | MIN. | MAX. | MIN. | MAX. | MIN. | MAX. |MM (IN.)| |--------|---------|---------|---------|---------|---------|---------|--------| | BB | 6.325 | 6.335 | | | 6.318 | | | | OD 5 |(0.2490) |(0.2494) | | |(0.2487) | | | | | | | 0.015 | 0.035 | | | 0.039 | | | | | (0.0005)| (0.0013)| | |(0.0015)| | BB | 6.350 | 6.360 | | | | 6.357 | | | ID 3 |(0.2500) |(0.2503) | | | |(0.2502) | | -------------------------------------------------------------------------------
R 1EFF : 001-049, 101-105, 151-199, 1 21-51-41Page 605 1 1 May 01/05 1 1 1CES 1 VALVE - PACK FLOW CONTROL (8HB,11HB,23HB,24HB) - SERVICING
__________________________________________________________
TASK 21-51-51-600-001
Scheduled Replacement of a Pack Flow-Control Valve Trailing-Edge Probe Filter
1. Reason for the Job
__________________
To clean or replace a contaminated flow-control valve trailing-edge probe filter.
NOTE : This procedure is only applicable for pack flow-control valves with
____ the part numbers which follow:-P/N 751A0000-07 Amendment ABC, P/N 751A0000-07 Amendment BC and, P/N 751B0000-02 Amendment AB. The procedure is the same for the pack flow-control valves 8HB and 11HB. For recommendations as to the intervals and methods to use to clean the filter refer to Airbus Industrie SIL 21-101 or Liebherr SB 751-21-01.
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s)
No specific Torque Wrench : range 0.00 to 1.20 m.daN
(0.00 to 9.00 lbf.ft)
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 04-014A USA MIL-PRF-907 HIGH TEMPERATURECOMPOUND (Ref. 20-31-00)
Material No. 19-009 USA AMS 5687 LOCKWIRE STAINLESS STEEL ANNEALED 0.5MM DIA (Ref. 20-31-00)
1EFF : ALL 1 21-51-51Page 301 1 1 Aug 01/05R 1 1 1CES 1
C. Expendable Parts
-------------------------------------------------------------------------------FIG.ITEM |DESIGNATION |IPC-CSN -------------------------------------------------------------------------------
2 seal 21-51-51 02 -020 2 seal 21-51-51 02B-020 3 filter 21-51-51 02 -010 3 filter 21-51-51 02B-010
D. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM AIR CONDITIONING 空調 3(127)
