B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 04-011 USA MIL-G-4343 SILICONE GREASE PNEUMATIC SYST AND SEALS (Ref. 20-31-00)
Material No. 15-004 USA MIL-C-16173 GRADE 3 CORROSION PREVENTIVE COMPOUND (Ref. 20-31-00)
1EFF : ALL 1 12-22-52Page 328 1 1 May 01/05R 1 1 1CES 1
C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
R 12-22-52-991-010 Fig. 307
3. Job Set-up
__________
Subtask 12-22-52-010-064
A. Get Access
(1)
Put the access platform in position below the closed FWD, lateral left, lateral right or AFT avionics compartment door as required.
(2)
Push the button of the external door handle at the applicable avionics compartment door so that it moves from its recess.
NOTE : Do not move the external door handle in the UNLOCK position at
____
this time.
4. Procedure
_________
Subtask 12-22-52-640-057
A. Lubrication of the External Door Handle R (Ref. Fig. 307/TASK 12-22-52-991-010)
(1)
Apply COMMON GREASE (Material No. 04-011) to the shaft of the external door handle at the Fwd avionics compartment door.
(2)
Apply COMMON GREASE (Material No. 04-011) to the shaft of the external door handle at the lateral left avionics compartment door.
(3)
Apply COMMON GREASE (Material No. 04-011) to the shaft of the external door handle at the lateral right avionics compartment door.
(4)
Apply COMMON GREASE (Material No. 04-011) to the shaft of the external door handle at the AFT avionics compartment door.
WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE
_______ THIS/THESE MATERIAL/S. USE PROTECTIVE CLOTHING, RUBBER GLOVES, GOGGLES AND A MASK.
(5) Remove any unwanted lubricant with a clean lint-free cloth.
R External Door Handle of Avionics Compartment Doors Figure 307/TASK 12-22-52-991-010
1EFF : 1 1 1CES ALL 1 111 12-22-52 Page 330 May 01/05
(6) Apply STORAGE PRESERVATION (Material No. 15-004) to the inner surface and the adjacent area of the applicable external door handle. ________
5. Close-up
Subtask 12-22-52-410-057
A. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Push the external door handle into its recess so that it is flush with the door contour.
(3)
Remove the access platform(s).
R 1EFF : ALL 1 12-22-52Page 331 1 1 May 01/05 1 1 1CES 1
TASK 12-22-52-640-009
Lubrication of the FWD and AFT Cargo-Compartment Door Handle
WARNING : MAKE SURE THAT THERE IS A GOOD FLOW OF AIR THROUGH THE WORK AREA WHEN
_______ YOU USE SPECIAL MATERIALS. IF YOU GET ONE OF THESE MATERIALS ON YOUR SKIN, IN YOUR MOUTH OR IN YOUR EYES : -FLUSH IT AWAY WITH A FLOW OF CLEAN WATER FOR BETWEEN 10 AND 15 MINUTES. -GET IMMEDIATE MEDICAL AID IF IRRITATION OCCURS. DO NOT BREATHE THE FUMES FROM THE MATERIAL. DO NOT SMOKE WHEN YOU USE THE MATERIAL. DO NOT USE THE MATERIAL NEAR A FLAME, SPARKS OR SOURCES OF HEAT. THESE MATERIALS ARE DANGEROUS : THEY ARE POISONOUS, FLAMMABLE AND SKIN IRRITANTS.
1. Reason for the Job
__________________
Refer to the MPD TASK: 523000-03
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s) No specific lint-free cloth R No specific access platform 2.0 m (6 ft. 7 in.) No specific adjustable access platform 3.5 m (11 ft. 6 in.)
R 1EFF : ALL 1 12-22-52Page 332 1 1 May 01/05 1 1 1CES 1
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION ------------------------------------------------------------------------------- 中國航空網 m.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：A320飛機維護手冊 AMM SERVICING 2(29)
