曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

SLAVEIRDR RDR
SLAM/INDEP INDEP
slAvErrcs TCS
DD CONTROL/SELECTION DDRESPONSE
ACCVAUTOS RCH AUTO SEARCH
ACCIIMAN MANUAL
ACQ/AUTO AUTO
VSUHI HI
VSUOFF OFF
vsl.no Lo
Figure 38-41. DD Responsesfo r SCU/SSP/DD
Select Tests
SHC CONTROUSELECTlON
HC MODE/IR/lV
HC MODEIRDR
HC MODE/TlD CURSOR
HC MODEIDD CURSOR
HANDGRIP ACTlON SWlTCH/
(NO DETENT)
HANDGRIP ACTION SWlTCH/
(FIRST DETENT)
HANDGRIP ACTION SWTTCH/
(FULL DETENT)
HCX (HANDGRIP) LEFT/RIGHT
HCY (HANDGRIP) FORE/AFT
MRL
OFFSET
DD RESPONSE
IRrrV
RDR
TlD CURSOR
DD CURSOR
NO
HALF
FULL
-99 to +99
-99 to +99
X
X
Figure 38-42. DD Responsesf or SHC SelectT ests
TID CONTROL/SELECTION DD RESPONSE
TRACK HOLD X
TlD MODErm C
Figure 3843. DD Responsesf or TID SelectT ests
ORIGINAL 38.58
NAVAIR 01.F14AAD-1
TCS
MAIN1
DISP
-
2
-
o-
-
2
-
4
-
INSTR
SPL
TEST
(NBR)
6 LI , 6
SPF
\
BIT
‘3
TCS
-
-
AL 22999 TGT
Figure 384. BIT Static DD Display (ATTK Selected)
38-57 ORIGINAL
NAVAIR 01.FUAAD-1
T*PE CONFIO”R*T,ON N”hf.sER
,INFORMATION FOR LOCATlON ONLY,
TARGET
CURSOR
SYMBOL
VELOCITY
VECTOR
CENTROIO
DOT
ARTlFlCAL
HORUON
SYMBOL STEERIN
SYMBOL
Figure 38-45. BIT Static TID Display (ATTK Selected)
These test patterns should be examined by the RIO
for the absence of any required symbols, symbol intensity,
and symbol position. During the running of the
static test, the RIO should also select half action or fall
action on the hand control. The RIO should ensure that
the TID cursor can be moved throughout the range of
the TID by moving the hand control. Upon release ofthe
action switch, the cursor symbols should return to their
original positions.
The static portion of the displays test gives the RIO
an indication that the computer does or does not have
the display capability for each of the indicated symbols.
It is more than a displays test because it also tests
computer ability to generate symbols needed for a
tactical situation. The computer assists the RIO in the
static portion of the displays test by monitoring power
failures that have occurred in the controls and displays
units. A DISP FAILED indicator will appear on the
maintenance display if a power failure is detected.
The maintenance display indicates DISP PASSED
until a failure occurs.
b. Dynamic Testing. The dynamic test consists of
a visual evaluation of the movement of the artificial
horizon, ASE circle, steering symbol, closing range rate
indicator, launch zone symbols, and a velocity vector
with MUIR and TUOR markers that sequentially vary in
size or position. A fixed initial point symbol is displayed
for reference. To enter the dynamic test, the RIO selects
CLEAR, NBR, 1, 1, and ENT on the DD keypad.
When the RIO selects ATTIC with the TID MODE
switch, the displays on the TlD and DD (Figures 38-38
and 38-39) will go through the following movements
every 2 seconds:
On the DD, the following occur simultaneously:
2. The artificial horizon steps in roll 6om O” to +15’
(right wing down), +30°, +45“, back to O”, -lSO(leI?
wing down), -30°, -45’, and back to 0’.
3. The ASE circle steps from 0.8 inch in diameter to
0.1,0.3,0.56,thenbackto0.8.
4. The steering symbol steps around the ASE circle
in a clockwise direction in steps from its position
in the upper right quadrant to the lower right,
lower left, upper left, then back to the upper right
quadrant.
ORIGINAL
NAVAIR 0%Fl4AAD-1
HALF OR FULL ACTION NOT SELECTED
TWS A
RDR 4 1,
2
MAINTDISP
4
INSTR
12
6
SPL
TEST
(NBR)
.
BIT
PHC I
\
AZIMVT” TIC MARK SCANS
6
Figure 3846. BIT Static DD Display (GND STAB or TV Selected) (Sheet 1 of 2)
30-59 ORIGINAL
HALF OR FULL ACTION NOT SELECTED
200 GM
NCTR MAN SNIFF
TEST
TGT
INS-W
SPL
TEST
(NBR)
BIT
1234
HALF OR FULL ACTION SELECTED
20GM
NCTR MAN SNIFF
+ +/h\
+
INSTR
SPi
TEST
WJBA)
BIT
G
Figure3 8-46.B IT StaticD D Display( GND STABo r TV Selected()S hee2t of 2)
ORIGINAL 38-80
NAVAIR 0%F14AAD-1
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：F-14D 飛行手冊 Flight Manual 3(84)