曝光臺 注意防騙 網(wǎng)曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

and be displayed. The operational day is loaded as
follows:
1. Perform steps 1 through 5 of paragraph 19.3.4.4.
Step 1 is not required if already in MWOD Load.
2. Frequency mode control - PRESET (last WOD
and segment selected will be displayed).
19-15 ORIGINAL
NAWAlR 0%F14AAD-l
3. Frequency select switches - Select 8.1.
4. Frequency mode control - READ (last operational
date or 00 is displayed).
5. Fmquency select switches - Selected Desired
Date.
6. Frequency mode control - LOAD (Operational
date is loaded into memory).
Note
Out of range (cl or >31) operational dates
may not be entered.
19.3.4.8 MWOD Verify. The aircrew may view the
MWODs at any time for verification by reading the
MWOD locations by using steps 1 through 3 in paragraph
19.3.4.5.
19.3.4.9 MWOD Erase. The following procedure
enables the aircrew to erase all MWODs stored in the
nonvolatile memory. This procedure is recommended
before reloading all MWODs with new hquencies.
1. Frequency mode control - PRESET.
2. CHAN SEL switch - Select Channel 40.
3. Frequency mode control - RBAD.
4. Frequency select switches - Select 220.050 To
Initiate MWOD Erase Function.
5. Function mode control - LOAD (display will
go blank indicating MWODs have been erased).
19.3.4.10 FM1 Training Frequency Load. The
Have Quick II FMT training net operates similar to
combat Have Quick II, as both the date tag and operational
day t%nctions are used. The FMT net, however,
hops on its own set of 16 frequencies loaded into a
separatetr aining WOD. Additionally, a specialM WOD
segment for FMT (300.0xX, where XX is the hop rate)
is loaded into the fast segment ofthe MWOD being used
(usually 1.1, but any of the six MWODs can be used as
long as the date tag for the MWOD whose fmt segment
contains 300.0xX matches the operational day). The
frequencies actually hopped on, however, are loaded
into a separateF MT WOD that can be accessedw ith the
FMT loadc odelo aded into presetc hannel4 0:Once the
16 training kequencies (7.01 through 7.16) m. loaded,
it is not necessaryto reload them. Additionally, it is not
necessary to reload the special FMT MWOD segment
once it is loaded, as long as the date tag used is within
the same MOOD as the special FMT segment. If using
the self-start method of TOD, the operational day as well
as the date tag must be loaded into segments 8.1 and I .7
(or the seventh segment of whichever MWOD is being
used), respectively. Thus, combat Have Quick II and
FMT can be used interchangeably simply by loading
one or more of the MWOD fmt segments with the
special training WOD segment. On every day that the
operational day matches the date tag of the MWOD with
the special FMT segment loaded into its fmt segment,
the unit will hou on the FMT trainine tiuencies. re
gardless ofthe &tents ofthe other se&en& within’that
MWOD. See Figure 19-10, Note 2.
1. Frequency mode control - PRESET.
2. CHAN SEL switch - Select Channel 40.
3. Frequency mode control - READ.
4. Frequency select switches - Select 220.075.
5. Frequency mode control - LOAD.
6. Frequency mode control - PRESET (fat FMT
frequency segment 7.01 is displayed).
7. Frequency select switch - Select Desired FMT
Segment.
8. Frequency mode control - READ.
9. Frequency select switches - Select Desired
FMT Training Frequency.
10. Frequency mode control - LOAD (desired
FMT training frequency is stored in memory).
11. Repeat steps 6 through 10 to load remaining desired
FMT training frequencies.T he load fbnction
is exited by placing the frequency mode control to
MAN.
19.3.4.11 FMT Nat Operation. Once the training
frequencies have been loaded or verified, Have Quick
II FMT net can be operated as follows:
1. Perform steps 1 through 5 of paragraph 19.3.4.4.
2. Frequency mode control - PRESET.
3. Frequency select switches - Select Segment 1
of Desired MWOD To Be Used (1.1, 2.1, 3.1,
etc.).
ORIGINAL 19-16
4. Frequency mode control - READ (display
shows frequency indicating desired WOD segment).
5. Frequency select switch - Select Special FMT
Segment With Desired Hop Rate (300.0xX XX =
00,25,50,75).
6. Frequency mode control - LOAD (desired frequency
loaded into memory).
7. Frequency mode control - PRESET.
8. Frequency select switches - Select Segment 7
(date tag) of the Same MWOD Used Above (1.7,
2.7,3.7, etc.).
9. Frequency mode control - READ (display
shows two-digit date tag previously loaded or 00).
10. Frequency select switches - Select Desired
　
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：F-14D 飛行手冊 Flight Manual 3(3)