曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

1.3 298.100 2.3 288.000 3.3 276.600 4.3 268.000 5.3 256.600 6.3 246900
1.4 297.000 2.4 287.900 3.4 277.400 4.4 267.000 5.4 257.600 6.4 247.100
1.5 296.000 2.5 286.300 3.5 276.500 4.5 266.700 5.5 256.000 6.5 246.100
1.6 295.000 2.6 285.300 3.6 275.100 4.6 265.500 5.6 255.500 6.6 245.200
1.7 11 2.7 12 3.7 13 4.7 14 5.7 15 6.7 16
5.1 = OPERATIONAL DAY
1 .l through 1.6 are WOD 1 segment numbers.
1.7 is the date tagfor WOD 1.
2.1 through 2.6 are WOD 2 segment numbers
2.7 is the date tag for WOD 2.
3.1 through 6.7 is the same as above for WOD’s 3 through 6.
6.1 is the current Operational Day, which should match one of the date tags.
Note:
(1) If the current operational day was 11 (MWOD location I), Have Quick II Combat net would be used with a
hop rate of 50 (included in the last two digits of segment 1 .l). An appropriate Have Quick II operatlonal net
should be chosen.
(2) If the current operational day was 16. Have Quick II Training Net would be used because the first
segment of MWOD location 6 (6.1) is the special training segment. The hop rate would be 50 (last two digits
of first segment). An appropriate Have Quick II Training Net number should be chosen.
Figure 19-10. Example ofan ARC-182 Have Quick Il MWOD Fill
ORIGINAL 19.14
NAVAIR 01-F14AAD-1
19.3.4.3 Time of Day. TOD is a signal that synchronizes
Have Quick radios to a common time for antijam
operation. There are two ways to enter TOD. One
method involves receiving UTC over the air on a manually
selectedU HF frequencya fter power up. The second
method involves using the self-start (emergency time
start) mode, which is used when acting as master clock
to transmit that time to other Have Quick systems.
Within this TOD signal is the operational day. This is
transmitted with the TOD or loaded manually as in the
self-startp rocedure.R efer to paragraph1 9.3.4.12,T OD
Load. The codeword for TOD is “Mickey.”
19.3.4.4 MWOD Load Entry
1. Frequency mode control - Preset.
2. CHAN SEL switch - Select Channel 40.
3. Frequency mode control - READ.
4. Frequency select switches - Select 220.025.
5. Frequency mode control - LOAD.
Note
If MWODs are being loaded to replace existing
ones, the old MWODs should be
erased using the procedures in paragraph
19.3.4.9. This procedure will erase all
MWODs in the radio’s memory.
19.3.4.5 MWOD Load
1. Frequency mode control - Preset (1.1 will be
displayed).
2. Frequency select switches - Select Desired
WOD and MWOD Segment Using Middle Two
Frequency Select Switches.
3. Frequencym ode control - READ (displays hows
frequency indicating desired WOD segment).
Note
If the MWODs were erased using the
MWOD erase procedure in paragraph
19.3.4.9,t he display will show 000.000i ndicating
that they had been erased.
4. Frequency select switches - Select Desired Frequency
WOD Segment.
5. Frequency mode control - LOAD (desired &equency
loaded into memory).
6. Repeat steps 1 through 5 to load remaining
MWODs.
Note
The desiredf requenciesa re loadedi n segments
1 through6ofeachMWOD. Thedate
tag for each I?WOD is loaded into the sovenths
egmenat ndi s a two-digit numberc orrespondingto
the operationadl ay on which
thatMWODistobeused.Itcanbeloaded
or changedu singt he two middle frequency
select switches and the MWOD segment
loadingp roceduresa bove.
The crew may not enter an out-of-range
WOD frequency, segment, or date tag.
When two identical date tags are loaded,
the last date entered is valid and the old
date is set to zero. Ifthe old date is viewed,
00 will be displayed.
‘Ike MWOD is not entered into the memory
of the unit until the date tag is loaded.
Thus, if a segment of an MWOD has been
changed after the MWOD was initially
entered,t he date tag must be reenteredt o
accept the MWOD change.
19.3.4.6 MWOD Load Exit
1. Frequency mode control - MAN (ready to receive
TOD).
Note
When manual is selected on the frequency
mode control to exit a load mode, the code to
operate in Have Quick II antijam without
entering a load mode (220.000) will automatically
be loaded into preset channel 40.
19.3.4.7 Operational Date Load. The operational
date is the calendar date of the mission day. The range
is 1 through 3 1. The MWOD that is used by the unit for
frequency hopping is the MWOD whose date tag
matches the operational day. Thus, if an operational day
is entered or received via TOD transmission and no date
tag exists for that operational day, an error will occur
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：F-14D 飛行手冊 Flight Manual 3(2)