曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

March 2010
8-28 Information Manual
Section 8 Cirrus Design
Handling, Servicing, Maintenance SR20
Windscreen and Windows
Before cleaning an acrylic window, rinse away all dirt particles before
applying cloth or chamois. Never rub dry acrylic. Dull or scratched
window coverings may be polished using a special acrylic polishing
paste.
• Caution •
Clean acrylic windows with a solvent free, none abrasive,
antistatic acrylic cleaner. Do not use gasoline, alcohol,
benzene, carbon tetrachloride, thinner, acetone, or glass
window cleaning sprays.
Use only a nonabrasive cotton cloth or genuine chamois to
clean acrylic windows. Paper towel or newspaper are highly
abrasive and will cause hairline scratches.
1. Remove grease or oil using a soft cloth saturated with kerosene
then rinse with clean, fresh water.
• Note •
Wiping with a circular motion can cause glare rings. Use an up
and down wiping motion to prevent this.
To prevent scratching from dirt that has accumulated on the
cloth, fold cloth to expose a clean area after each pass.
2. Using a moist cloth or chamois, gently wipe the windows clean of
all contaminates.
3. Apply acrylic cleaner to one area at a time, then wipe away with a
soft, cotton cloth.
4. Dry the windows using a dry nonabrasive cotton cloth or chamois.
March 2010
Information Manual 8-29
Cirrus Design Section 8
SR20 Handling, Servicing, Maintenance
Engine Compartment
Before cleaning the engine compartment, place a strip of tape on the
magneto vents to prevent any solvent from entering these units.
1. Place a large pan under the engine to catch waste.
2. Remove induction air filter and seal off induction system inlet.
3. With the engine cowling removed, spray or brush the engine with
solvent or a mixture of solvent and degreaser. In order to remove
especially heavy dirt and grease deposits, it may be necessary to
brush areas that were sprayed.
Do not spray solvent into the alternator, vacuum pump, starter,
or induction air intakes.
4. Allow the solvent to remain on the engine from 5 to 10 minutes.
Then rinse engine clean with additional solvent and allow it to dry.
• Caution •
Do not operate the engine until excess solvent has evaporated
or otherwise been removed
5. Remove the protective tape from the magnetos.
6. Open induction system air inlet and install filter.
7. Lubricate the controls, bearing surfaces, etc., in accordance with
the Lubrication Chart.
Landing Gear
Before cleaning the landing gear, place a plastic cover or similar
material over the wheel and brake assembly.
1. Place a pan under the gear to catch waste.
2. Spray or brush the gear area with solvent or a mixture of solvent
and degreaser, as desired. Where heavy grease and dirt deposits
have collected, it may be necessary to brush areas that were
sprayed, in order to clean them.
3. Allow the solvent to remain on the gear from five to ten minutes.
Then rinse the gear with additional solvent and allow to dry.
4. Remove the cover from the wheel and remove the catch pan.
5. Lubricate the gear in accordance with the Lubrication Chart.
March 2010
8-30 Information Manual
Section 8 Cirrus Design
Handling, Servicing, Maintenance SR20
Cleaning Interior Surfaces
Seats, carpet, upholstery panels, and headliners should be vacuumed
at regular intervals to remove surface dirt and dust. While vacuuming,
use a fine bristle nylon brush to help loosen particles.
• Caution •
Remove any sharp objects from pockets or clothing to avoid
damaging interior panels or upholstery.
Windshield and Windows
Never rub dry acrylic. Dull or scratched window coverings may be
polished using a special acrylic polishing paste.
• Caution •
Clean acrylic windows with a solvent free, none abrasive,
antistatic acrylic cleaner. Do not use gasoline, alcohol,
benzene, carbon tetrachloride, thinner, acetone, or glass
window cleaning sprays.
Use only a nonabrasive cotton cloth or genuine chamois to
clean acrylic windows. Paper towel or newspaper are highly
abrasive and will cause hairline scratches.
• Note •
Wiping with a circular motion can cause glare rings. Use an up
and down wiping motion to prevent this.
To prevent scratching from dirt that has accumulated on the
cloth, fold cloth to expose a clean area after each pass.
1. Using a moist cloth or chamois, gently wipe the windows clean of
all contaminates.
2. Apply acrylic cleaner to one area at a time, then wipe away with a
soft, cotton cloth.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：西銳20飛機信息手冊 SR22 AIRPLANE INFORMATION MANUAL 1148-126(88)