曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

adjust the seat forward. Recline position is controlled through levers
located on each side of the seat backs. Depressing the recline release
control while there is no pressure on the seat back will return the seat
back to the full up position.
• Caution •
The seat bottoms have an integral aluminum honeycomb core
designed to crush under impact to absorb downward loads. To
avoid crushing this core, do not kneel or stand on the seats.
To position front seat fore and aft:
1. Lift the position control handle.
2. Slide the seat into position.
3. Release the handle and check that the seat is locked in place.
To adjust recline position:
1. Actuate and hold the seat back control lever.
2. Position the seat back to the desired angle.
3. Release the control lever.
Each rear seat consists of a fixed seat bottom, a folding seat back, and
a headrest. The seat backs can be unlatched from inside the baggage
compartment and folded forward to provide a semi-flat surface for
bulky cargo extending forward from the baggage compartment.
March 2010
7-30 Information Manual
Section 7 Cirrus Design
Airplane Description SR20
To fold seat back forward:
1. From the baggage access, lift the carpet panel at lower aft edge of
seat to reveal the seat back locking pins (attached to lanyards).
2. Remove the locking pins and fold seat forward.
Windshield and Windows
The windshield and side windows are manufactured of acrylic. Use
only clean soft cloths and mild detergent to clean acrylic surfaces.
Refer to Section 8 for detailed cleaning instructions.
Cabin Safety Equipment
Passenger Restraints
Integrated seat belt and shoulder harness assemblies with inertia
reels are provided for the pilot and each passenger. The rear seat
belts are attached to fittings on the floorboard and the forward seat
belts are attached to the seat frame. The shoulder harnesses are
attached to inertia reels mounted in the seat back for the front seats
and on the baggage compartment rear bulkhead for the rear seats.
Each harness is attached to the seat belt. The buckle half of each
assembly is on the left-hand side and the link half is on the right-hand
side. The inertia reels allow complete freedom of movement of the
occupant’s upper torso. In the event of a sudden deceleration, the
reels lock automatically to protect the occupants.
Serials 1005 thru 1267 after SB 2X-25-14; An inflatable shoulder
harness is integral to each crew seat harness. The electronic module
assembly, mounted below the cabin floor, contains a crash sensor,
battery, and related circuitry to monitor the deceleration rate of the
airplane. In the event of a crash, the sensor evaluates the crash pulse
and sends a signal to an inflator assembly mounted to the aft seat
frame. This signal releases the gas in the inflator and rapidly inflates
the airbag within the shoulder harness cover, After airbag deployment,
the airbag deflates to enable the pilot/co-pilot to egress the aircraft
without obstruction.
The crash sensor’s predetermined deployment threshold does not
allow inadvertent deployment during normal operations, such as hard
landings, strikes on the seat, or random vibration.
March 2010
Information Manual 7-31
Cirrus Design Section 7
SR20 Airplane Description
• Caution •
No slack may exist between the occupant’s shoulder and
restraint harness shoulder strap.
Stow the seat belts in the latched position when not in use.
To use the restraints:
1. Slip arms behind the harness so that the harness extends over
shoulders.
2. Hold the buckle and firmly insert the link.
3. Grasp the seat belt tabs outboard of the link and buckle and pull to
tighten. Buckle should be centered over hips for maximum comfort
and safety.
4. Restraint harnesses should fit snug against the shoulder with the
lap buckle centered and tightened around the hips.
To release the restraints:
1. Grasp the top of the buckle opposite the link and pull outward. The
link will slip free of buckle.
2. Slip arms from behind the harness.
Emergency Egress Hammer
An eight-ounce ball-peen type hammer is located in the center armrest
accessible to either front seat occupant. In the event of a mishap
where the cabin doors are jammed or inoperable, the hammer may be
used to break through the acrylic windows to provide an escape path
for the cabin occupants.
Fire Extinguisher
A liquefied-gas-type fire extinguisher, containing Halon 1211/1301
extinguishing agent, is mounted on the forward inboard side of the
pilot’s seat base. The extinguisher is approved for use on class B
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：西銳20飛機信息手冊 SR22 AIRPLANE INFORMATION MANUAL 1148-126(59)