曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

altitude. If the airplane’s altitude deviates ± 300 feet from the
selected altitude, the chime will sound and the ALR annunciator
will flash to indicate the condition.
2. To disable ALR, press the altitude selector ALR button again. The
ALR annunciator will go out.
GPS Tracking and GPS Approach
1. Begin with a reliable GPS signal selected on the NAV receiver.
2. Select desired course on HSI and establish a desired intercept
heading.
3. Press the NAV button on the autopilot programmer/computer
twice. The NAV and GPSS mode annunciators will illuminate.
• Note •
If the course needle is at full-scale deviation, the autopilot will
establish the airplane on a heading for a 45° intercept with the
selected course. As the airplane approaches the course, the
autopilot will smoothly shallow the intercept angle. The pilot
may select an intercept angle less than the standard 45° by
setting the desired intercept heading with the HSI HDG bug,
pressing and holding HDG, and then pressing NAV once to
Revision 4: 07-18-05
16 of 24 P/N 13772-108
Section 9 Cirrus Design
Supplements SR22
intercept course in NAV mode or twice to intercept course in
GPSS mode on the autopilot programmer/computer. When
the on-course intercept turn begins the HDG mode will
disengage and the annunciator will go out.
During the intercept sequence, the autopilot operates at
maximum gain and sensitivity (90% of standard rate turn).
When the selected course is intercepted, course deviation
needle centered, the course-tracking program is activated.
The system will remain at maximum sensitivity for
approximately 15 seconds while the wind correction angle is
established. The maximum turn rate is then reduced to 45%
standard rate. Approximately 60 seconds later, the maximum
turn rate is reduced to 15% standard rate.
4. For increased sensitivity during GPS approach or if desired for
enroute tracking, press the APR button on the autopilot
programmer/computer. The NAV, GPSS, and APR annunciators
will be illuminated. Use HDG to accomplish a procedure turn.
Engage GPSS again to complete the approach.
VOR Tracking and VOR-LOC Approach
1. Begin with a reliable VOR or VOR-LOC signal selected on the
NAV receiver.
2. Select desired course on HSI and establish a desired intercept
heading.
3. Press the NAV button on the autopilot programmer/computer. The
NAV mode will illuminate. Course interception and tracking will be
as described under GPS Tracking and GPS Approach above.
4. For station passage, set HDG bug to within 5° of selected course.
• Note •
If the HDG bug is within 5° of center and the course deviation
is less than 10%, the autopilot will immediately establish the
lowest level of sensitivity and limit the turn rate to a maximum
of 15% of a standard rate turn.
5. For increased sensitivity during approach or if desired for enroute
tracking, press the APR button on the autopilot programmer/
computer. Both NAV and APR annunciators will be illuminated.
Revision 4: 07-18-05
P/N 13772-108 17 of 24
Cirrus Design Section 9
SR22 Supplements
Glideslope Intercept and Tracking
1. Begin with a reliable ILS signal selected on the NAV receiver.
2. Select autopilot NAV and APR. Airplane must be within 50%
needle deviation of localizer centerline.
3. Select ALT mode. Airplane must be 60% or more below the
glideslope centerline during the approach to the intercept point. If
the above conditions have existed for 10 seconds, GS mode will
arm, the GS annunciator will come on and the ALT annunciator will
remain illuminated. When glideslope intercept occurs, the ALT
annunciator will go out and the system will track the glideslope.
• Note •
If approach vectoring locates the airplane too near the
glideslope at the intercept point (usually the outer marker), the
GS mode can be manually armed by pressing the ALT button
once. Once capture is achieved, GS annunciator will come on
and ALT annunciator will go out.
Section 5 - Performance
There is no change to the airplane performance when the S-Tec
System 55X autopilot is installed.
Section 6 - Weight & Balance
There is no change to the airplane weight & balance when the S-Tec
System 55X autopilot is installed.
Section 7 - Systems Description
Autopilot
The airplane is equipped with an S-Tec System 55X two-axis
Automatic Flight Control System (Autopilot). The autopilot
programmer/computer is installed in the center console radio stack.
The autopilot roll axis uses an inclined gyro in the turn coordinator
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：AIRPLANE INFORMATION MANUAL for the CIRRUS DESIGN SR22(117)