曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

o IRS switches (1-3) Align
o  FMC:
 Ident page 1L
 Pos Init page 6R
 Copy GPS Position 4R (alternative enter 4-letter airport code & press 2L)
 Paste to IRS Pos. 5R (alternative copy airport position to IRS; 2R  4R)
o IRS switches (1-3) Nav
• Fuel Pumps Off (CTR, STAB, MAIN 1 and 4, OVRD & MAIN 2 and 3)
• Fuel X-Feed On (4 switches)
• Nacelle Anti-Ice Off
• Wing Anti-Ice Off
• Window Heat Enable
• Yaw Dampers On
• APU switch Start
---wait till APU Gens available---
• APU Gen Switches 1 & 2 On
• PASSenger TEMPerature Auto
• FLT DECK (temperature) Auto
• Trim Air On
• Upper Recirculation Fan On (Upr Recirc)
• Lower Recirculation Fan On (Lwr Recirc)
• Gasper On
• Pack switches (1-3) Norm
• ISLN switches L & R Open (“Valve” extinguished)
• APU Bleed (abv Eng Bleed) On
End OVHP only
• FMC
- Clear messages  CLR
- Route Page RTE
- Enter company route [read: enter flightplan-name (created in FSBuild)]  3R
- Activate  6R  Exec
- Performance initialization page  6R
- Enter FL / altitude  1R (max FL for 747 = FL410)
- Gross Weight auto function  1L
- Enter fuel reserve in %  4L
- Enter Cost Index (50 to 100)  5L
- Thrust Limit page  6R
- Modify Thrust settings if needed
- Takeoff page  6R
- Enter flaps setting (standard 20)  1L
- Verify V1, VR and V2  1R  2R  3R (remember V2 speed)
- Verify takeoff trim settings  4R (remember trim number)
-
• IVAP-flightplan Read from FMC & note/enter in IVAP FP
• Speed at flightplan Enter TAS (calculate: KIAS + FL/2) or MACH
• Departure Time Enter (UTC to CET  CET -2 (winter -1))
• EFIS-Mode (MainPanel/MP) MAP
• EFIS-Range (MP) 40nm (or as required)
• GND-Control Set frequency (active ATC or Unicom 122.8)
• IFR-clrc Request (when ATC active)
• FP-correction Correct (if required / requested)
• IFR-clrc-data Note (Squawk, First-Altitude, QNH  Readback)
• Squawk Set
• Altimeter Set to actual atmospheric pressure (B)
• F/D (AP) On
• V2 (AP) Enter V2 speed to IAS/MACH indicator of AP
• LNAV (AP) Arm
• VNAV (AP) Arm
• First Alt (AP) Set
• AP Disengage Bar Up
• Fuel Control Switches (TP) Cutoff (Throttle Panel)
• Trim settings (TP) Check (same as FMC) (NUM1/7 with NUM off)
• Autobreak RTO
• TCAS switch Stby/Test
---wait till TCAS test finished---
• TCAS switch TA/RA
• TCAS biasing mode Above
• No Smoking On (or Auto)
• Seat Belts Auto
• FLT DK Door Lock
• TFC button (EFIS) Press (and check potential traffic)
---open Overhead panel & EICAS panel---
• Fuel Button (EICAS) Press & check fuel
• Fuel pumps On (all fuel pumps of tanks containing fuel)
---wait till fuel pumps rdy (green light)---
• Xfeed Set
o Tank 2 > Tank 1 Xfeed 1 on
o Tank 3 > Tank 4 Xfeed 2 on
o Otherwise Xfeed off
• Gangway disable (strg + j)
Engine s/u & Pushback:
• Doors closed
• Engine s/u & Pushback p/b clrc request
• Beacon Light On
• Hydraulic Demand pump switches 1-3 Auto
• Hydraulic Demand pump switch 4 Aux (check)
• Pack 1 On
• Pack 2 & 3 Off
• Engine Bleed Air switches On
• EICAS Open Engines Page
• EICAS Clear EICAS messages (Cacl Btn.)
• Parking break Off
• Pushback Start
• Engine Start Procedure:
o Autostart:
 Autostart On
 Continuous Ignition On
 Fuel Control Swt. 1 – 4 Run
 Engine 1 & 4 Start Sel. Pull
---wait till Engine 1 & 4 back at idle---
 Engine 2 & 3 Start Sel. Pull
o No Autostart:
 Autostart Off
 Continuous Ignition On
 Engine 1 & 4 Start Sel. Pull
---wait till N2% RPM reaches magenta line (14%)---
 Fuel Control Swt. 1 & 4 Run
---wait till Engine 1 & 4 back at idle---
 Engine 2 & 3 Start Sel. Pull
---wait till N2% RPM reaches magenta line (14%)---
 Fuel Control Swt. 2 & 3 Run
• APU Off
• APU Bleed Air Off
• Packs Norm (all)
• Hydraulic Demand pump switch 4 Auto
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：航空資料28(43)