曝光臺 注意防騙 網(wǎng)曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費(fèi)者

port of your computer…

Connect the DC power adapter to the FCU320 (Figure 2 “A”) and plug the adapter to a main supply
socket. The computer has to be switched on when you connect the FCU for the first time…
Figure 2: Connectors (back view)
A
C
B
H
D
F
E
G
FCU320
4
WARNING! FCU320 accepts a supply voltage of 6Vdc. Only provided stabilized plug-in power supply
adapter must be used; do not attempt to plug in a different adapter to FCU as you may irreparably
damage it.

The driver installation procedure will start automatically; follows the instruction on the screen (note that
the figure of the following example may be different depending by your operating system)…
When you will ask to connect to Menus Update to
search for software select “No, not this time” and
click next to continue…
Select “Install from a list or specific location” and
click next to continue…
Browse the temporarily folder where you have
unzipped the files and click next to continue…
You will be informed that the driver has not
been subordinate to Menus Logo testing click
“Continue Anyway”…
The drivers will be installed in the system; click “Finish” when prompted.
Important note: Depending by the system you may be required to repeat the driver installation two
times.
During the USB drivers installation the system assign a number to the communication port. Check your
configuration in the Windows Control panel -> System Property -> Device Manager Tab. On the (COM &
LPT) port you will see “CPflight serial adapter (COM n)” where “n” is the assigned communication port
number, you will use this number in the First set up (se following).
FCU320
5
FIRST SET UP AND START-UP
Project Magenta: To enable communication with Project Magenta you have to set the communication port.
In the Project Magenta FCU folder open “FCU.ini” file with a text editor, browse the [Serial Connection]
section and set CpflightComm= n where “n” is the communication port assigned by the system during the
USB drivers installation (see the above “Driver Installation” section). Save the “FCU.ini” file.
AST: to enable the communication install the AST Interface software for CPFlight FCU/EFIS Unit; download
the file at Airsimtech website download page. To enable the communication set the communication port
number in the enclosed ini file. Open the ini file with a text editor, in the Serial channel section set channel =
n where “n” is the communication port assigned by the system during the USB drivers installation (see the
above “Driver Installation” section).
Run Project Magenta FCU (or CPflightFCUinterface.com if used with AST) software to start-up the FCU.
The FCU320 will show on the displays the installed Firmware revision and the device serial number, and
then synchronize data.
The FCU turns off command come from the computer when you close the Project Magenta FCU (or AST)
software. If you shut-down the computer without exit the program, or a computer block occur, the FCU may
stay on or may fail the subsequent turn on. If you find any problem with the FCU start or turn off, it is
advisable to reset the unit. To do this, disconnect the power supply from the FCU, wait few seconds and
reconnect power.
Important notes! The FCU can extinguish the displays to simulate a "cold and dark" situation
depending by the battery, avionics or other aircraft systems status. Be sure to have the right
conditions in the cockpit to have the display turned on - The 3 positions toggle switches of EFIS
selectors (ADF/OFF/VOR) have lock lever, pull the lever to move in the new position.
Display bias angle
The bias angle is the angle from the perpendicular
from which an LCD display is best viewed. The bias
angle is often stated with reference to a clock face.
The FCU320 display is designed for 6:00 viewing
angle, this mean that the display is better visible from
the perpendicular to the bottom. The better display
viewing angle is from the perpendicular to 60° bottom
(see Figure 3). The horizontal viewing angle is 140°.
These are the better viewing condition for the
expected placement in the cockpit.
ON-FLY DISPLAY BRIGHTNESS AND BACKLIGHT REGULATION
When the FCU is normal running (starts with Project Magenta or in test mode using the CPflight
software test) you can on-fly set the display brightness and contrast, besides the backlight intensity.
This function is not available if the related preferences are settled “On” in the configuration menu
　
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：航空資料10(71)