曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

was Approved by Airbus
NNeeww PPrroodduuccttss
† ALNOVI is a registered trademark of Furukawa-Sky
Aluminum Corp.
Furukawa Review, No. 26 2004 61
Superplastic 5083 Aluminum Alloy Sheet “ALNOVI-1” was Approved by Airbus
have already participated in the A380 program for an
ultrahigh-capacity aircraft.
This is the first time that superplastic 5000 aluminum
alloys are applied for aircraft parts, and it is expected that
the demand expands during the course of strengthening
the cooperative relationship between Airbus S.A.S. and
Japanese corporations.
[Properties of ALNOVI-1]
Chemical compositions (mass%)
Mg Mn Cr Fe Si Al
4.5 0.7 0.12 < 0.1 < 0.1 Bal
Mechanical properties
Tensile strength
(N/mm2)
Proof strength
(N/mm2)
Elongation
(%)
Fatigue strength
107 (N/mm2)
310 160 28 150
Formability
Superplastic elongation (%) m-value
300 0.5
[Manufacturing Limits of ALNOVI-1]
Original sheet
Thickness: 0.3~3.0 mm
Width: 2000 mm, maximum
Length: 9500 mm, maximum
* Thermal refining is usually “H18”.
* Please ask us for other sizes.
Formed product
Width: 1000 mm, maximum
Length: 2150 mm, maximum
Depth: 250 mm, maximum
* The manufacturing limits for formed products depend
on the forming machine. Please ask us for details.
For more information, please contact:
Technical Research Center, Furukawa-Sky Aluminum
Corp.
1351 Uwanodai, Fukaya-city, Saitama 366-3511, JAPAN
TEL: +81-48-572-1318 FAX: +81-48-573-4418
Sky Aluminum Products Corp.
1351 Uwanodai, Fukaya-city, Saitama 366-3511, JAPAN
TEL: +81-48-571-0004 FAX: +81-48-572-1361
quantity production but for production of high-value
added parts or small- to medium-lot parts ranging
from 50 to 10000 pieces.
8) Cavity defects are liable to be generated by blow
forming. Too much cavity decreases the static and
fatigue strengths of the products.
Blowing pressure:
5 kgf/cm2
Temperature: 500˚C
Brought out
Ceiling plate
Die
Superplastic material
Formed product
Figure 1 Illustration of typical superplastic forming.
2.3 Major Uses of ALNOVI-1 Hitherto
• Body panel and optional parts for automobiles
• Fuel tank for two-wheeled vehicles
• Leisure boat
• Floor sheet and interior panel for vehicles
• Exterior wall, interior wall, ceiling and access floor
sheets for buildings
• Door, gate and fence for residence
• C a s i n g o f e l e c t r o n i c e q u i pme n t f o r me d i c a l
applications
• Ornaments, craftworks, etc.
3. APPROVAL BY AIRBUS
In March 2002, the Fukaya Works of Furukawa-Sky
Aluminum underwent a preliminary inspection. The next
month, Airbus inspectors came from UK and examined
the factory and quality management system officially. In
June, we obtained the factory approval. We prepared
a quality management manual for material production,
and then acquired the material approval for “ALNOVI-1”
in May 2003. In November of the year, we press released
that “ALNOVI-1” was approved as a material for the
landing lamp drum assembly for Airbus A330/A340.
Recently, three Japanese corporations joined the
A300/A340 program, while fifteen Japanese corporations
45246 Federal Register / Vol. 69, No. 145 / Thursday, July 29, 2004 / Rules and Regulations
with Airbus Service Bulletin A320–71–1030,
dated February 27, 2003, terminates the
requirements of this AD.
Note 1: Airbus Service Bulletin A320–71–
1030 refers to International Aero Engines
Information Bulletin V2500–NAC–70–0736,
dated January 28, 2003, as an additional
source of information for the harness/
connector replacement specified in
paragraph (h) of this AD.
Alternative Methods of Compliance
(AMOCs)
(i) The Manager, International Branch,
ANM–116, has the authority to approve
AMOCs for this AD, if requested in
accordance with the procedures found in 14
CFR 39.19.
Material Incorporated by Reference
(j) Unless this AD specifies otherwise, you
must use Temporary Revision 4.02.00/20,
dated May 3, 2004, to the Airbus A318/319/
320/321 Airplane Flight Manual; and Airbus
Service Bulletin A320–71–1030, dated
February 27, 2003; as applicable; to perform
the actions that are required by this AD.
(Only page 1 of the temporary revision
contains the date of the document.) The
Director of the Federal Register approves the
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：航空資料10(116)