曝光臺 注意防騙 網(wǎng)曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費(fèi)者

professional or commercial environments is not permitted without approval of the CPflight management;
please contact us at info@cpflight.com if you need to exploit our products in professional or commercial
environments.
FCU320 is a full scale replica of the Airbus 320/340 Flight Control Unit, look and functionality are reproduced
with high details. FCU320 is equipped with high quality level components; custom made LCD display and
Push/pull knobs give a high fidelity performances and a never seen realism.
FCU320 interface with Project Magenta FCU software and AST advanced version software; it is important to
know that the hardware have not its own intelligence on board, it establish an interface with the software;
logics, operating modes and aircraft behavior are managed by Project Magenta or AST software. The use of
this hardware presuppose to be familiar with Project Magenta (or AST) software.
The FCU320 does not interface directly with Microsoft Flight simulator or with other software add-on.
HARDWARE INSTALLATION
WARNING! The panels back cover are made with stainless still metal sheet, pay particular attention
to the cutting edges when you handle the panels.
The FCU320 is designed for panel assembly. The FCU320 is intended as a part to be inserted an a cockpit
reproduction, CPflight does not produce chassis or other mechanical parts for the cockpit structure, so the
panel is intended to be inserted in your own cockpit glare shield. To fix the FCU in your cockpit, cut out your
glare shield panel according with the dimensions quoted at the last pages of this manual. The FCU is
provided for “Captain only” configuration (FCU + left EFIS), or in a full configuration (FCU + Captain EFIS +
F/O EFIS), in the panel fixing cut-out consider the front-plates overhang to keep enough space to place the
EFIS’s.
The FCU units has to be fixed before to place the EFIS’s, differently you will not able to screw the fixing nuts.
Fix the FCU through the 4 fixing nuts (see figure 1); connect the EFIS’s flat cables and place EFIS’s in theirs
location. EFIS’s are fixed through 3 nuts.
Figure 1: FCU fixing
FCU320
3
CONNECTIONS
The FCU is provided with a universal supply adapter that accepts a voltage of 100 to 240Vac (50/60Hz).
Supply adapter and USB cable are provided with the FCU, you don’t need further hardware to operate.
Sockets for connections are on the back of panel (Figure 2). The two 20 pole sockets on sides (Figure 2 E
and F) are provided for EFIS’s connection; connect the flat cable of each EFIS to these sockets.
WARNING! Do not invert the connection of right and left EFIS, the two EFIS’s have different internal
circuit and this could damage both the FCU and EFIS.
In a network system, the FCU320 hardware has to be connected to the computer where the Project Magenta
FCU software runs. Even if Project Magenta (and CPflight) FCU may run on a client, in most of case the data
update result more fast if Project Magenta (and CPflight) FCU run on the server. Beyond to the EFIS
connection, supply and USB connectors the FCU320 have some further sockets: they are provided to allow
system expandability. A 16-pin connector “D” allows input/output connection, while DIN 5 pole socket “C” is
used to link auxiliary CPflight modules, both connectors are predisposed for future development. Close to the
left EFIS connection socket, there are the two jumpers for firmware upgrade and a small 2-pole socket ready
for external backlight control.
A - Power supply socket
B - USB
C - 5 poles DIN socket for external module connection
D - Input/Output (I/O) expansion socket (future development)
E - Left EFIS connection
F - Right EFIS connection
G - External Backlight control
H - Jumpers for firmware upgrade
WARNING! For D and G auxiliary connector refer to “AUXILIARY INPUTS” section later on this
manual. Do not attempt to connect anything different from as described in this section; warranty
does not cover damages due to incorrect wiring of any external device.
Note: If you do not use FCU320 for a long time it is preferable to disconnect the power supply.
USB DRIVER INSTALLATION
When you connect the FCU for the first time you will asked for the driver installation, the drivers are available
for download at CPflight website. To install the drivers follows these steps:

Download the file “usb.zip” at http://www.cpflight.com/sito/downloads/downloads.asp

Files are in a compressed archive .zip; unzip the files in a temporarily folder…

Connect the USB cable to the FCU320 USB connector (Figure 2 “B”) and the other side to a free USB
　
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：航空資料10(70)