曝光臺 注意防騙 網(wǎng)曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費(fèi)者

Note For strict liability, see section 6.1 of the Criminal Code.
(1B) Paragraph (1) (b) ceases to have effect on 30 November 2003.
(2) This regulation does not apply to the following:
(a) parts manufactured in the course of maintenance by a
maintenance organisation having approval to manufacture the
parts;
(b) parts produced under a type certificate or production certificate;
(c) parts manufactured by the owner or operator of an aircraft,
aircraft engine or propeller manufactured by the owner or
operator, for maintaining or altering the aircraft, aircraft engine
or propeller;
(d) parts produced under an ATSO authorisation;
(e) standard parts (such as bolts and nuts) conforming to established
industry or Australian specifications.
(2A) Any person is eligible to apply for an APMA.
(3) An application for an APMA may be made to CASA and must
include the following:
(a) the identity of the aircraft, aircraft engine or propeller on which
the part is to be installed;
(b) the name and address of the manufacturing facilities at which the
part is to be manufactured;
(c) the design of the part, which consists of:
(i) drawings and specifications necessary to show the
configuration of the part; and
Civil Aviation Safety Regulations 1998 (CASR)
Office of Legal Counsel CASR – 1st Edition – January 2003
Civil Aviation Safety Authority Replacement Page – Amdt No 5: Effective 27 November 2003
Part 21 — 100
(ii) information on dimensions, materials, and processes
necessary to define the structural strength of the part;
(d) test reports and computations necessary to show that the design
of the part meets the airworthiness requirements of these
regulations applicable to the aircraft, aircraft engine or propeller
on which the part is to be installed, unless the applicant shows
that the design of the part is identical to the design of a part that
is covered under a type certificate. If the design of the part was
obtained by a licensing agreement, evidence of that agreement
must be furnished;
(e) subject to subregulation (3A), a copy of the system that the
applicant proposes to use, if granted an APMA, to comply with
the requirements of subregulation 21.303 (11).
(3A) An applicant is not required to include a copy of the system referred
to in paragraph 21.303 (3) (e) if the applicant has previously given
CASA a copy of the same version of the system.
(4) An applicant is entitled to an APMA for a replacement or
modification part if:
(a) following examination of the design, or on the basis of design
data for the design approved by CASA or an authorised person,
CASA is satisfied that the design meets the airworthiness
requirements of these Regulations applicable to the aircraft,
aircraft engine or propeller on which the part is to be installed;
and
(b) the applicant will, if the APMA were to be granted, be able to
comply with the requirements of subregulation (11).
(5) An applicant for an APMA must allow CASA to make any inspection
or test necessary to determine compliance with the applicable
regulations.
(6) CASA is not required to consider an application unless the applicant
has complied with paragraphs (8) (b), (c) and (d).
(7) The applicant must ensure that no change is made to a part between
the time compliance with paragraphs (8) (b), (c) and (d) is shown for
that part and the time the part is presented to CASA for inspection or
test.
(8) An applicant for an APMA must make all inspections and tests
necessary to determine the following:
(a) compliance with the applicable airworthiness requirements;
(b) that materials conform to the specifications in the design;
(c) that the part conforms to the drawings in the design;
(d) that the fabrication processes, construction, and assembly
conform to those specified in the design.
Civil Aviation Safety Regulations 1998 (CASR)
CASR – 1st Edition – January 2003 Office of Legal Counsel
Replacement Page – Amdt No 5: Effective 27 November 2003 Civil Aviation Safety Authority
Part 21 — 101
(9) CASA must issue an APMA to an applicant for the APMA if the
applicant:
(a) is eligible, under this regulation, to apply for the APMA; and
(b) applies for the APMA in accordance with this Subpart; and
(c) is entitled, under this Subpart, to the APMA; and
(d) otherwise complies with this Part.
(10) CASA is not required to issue an APMA if the manufacturing
facilities for the part are located outside Australian territory, unless
the location of the manufacturing facilities places no undue burden on
CASA in administering the applicable airworthiness requirements.
　
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：澳大利亞CASR Civil Aviation Safety Regulations上(90)