曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

facilities to determine whether the applicant has complied with
regulations 21.139 and 21.143.
Source FARs section 21.135 modified.
21.137 Location of manufacturing facilities
Despite subregulation 21.134 (1), CASA is not required to issue a
production certificate if the manufacturing facilities concerned are
located outside Australian territory, unless there is no undue burden
on CASA in administering the applicable requirements of these
regulations.
Source FARs section 21.137 modified.
21.139 Quality system
An applicant for a production certificate must show that the applicant
has established, and can maintain, a quality system so that:
(a) each Class I product to be manufactured under the certificate will
conform to the type design for the product; and
(b) each Class II, Class III or unapproved Class I product to be
manufactured under the certificate will conform to the product
design for the product.
Source FARs section 21.139 modified.
Civil Aviation Safety Regulations 1998 (CASR)
CASR – 1st Edition – January 2003 Office of Legal Counsel
Replacement Page – Amdt No. 5: Effective 27 November 2003 Civil Aviation Safety Authority
Part 21 — 57
21.143 Quality system data requirements: prime manufacturer
(1) An applicant for a production certificate must submit to CASA, for
approval, a manual describing the inspection and test procedures
necessary to ensure that each product manufactured under the
production certificate is in a condition for safe operation and
conforms to:
(a) for a Class I product — the type design; and
(b) for a Class II, Class III or unapproved Class I product — the
product design.
(1A) The manual mentioned in subregulation (1) must include any of the
following that apply to the product:
(a) a statement describing how responsibilities are assigned and
authority is delegated in the quality system organisation, together
with a chart indicating:
(i) the functional relationship of the quality system
organisation to management and to other organisational
components; and
(ii) the chain of authority and responsibility within the quality
system organisation;
(b) a description of:
(i) the inspection procedures for raw materials, purchased
items and parts and assemblies produced by
manufacturers’ suppliers; and
(ii) the methods used to ensure that parts and assemblies that
cannot be completely inspected when delivered to the
production certificate holder’s plant are acceptable;
(c) a description of:
(i) the production inspection system for individual parts and
complete assemblies; and
(ii) the methods used for the identification of any special
manufacturing processes involved; and
(iii) the means used to control the processes; and
(iv) the final test procedure for the product; and
(v) in the case of a Class I product that is a completed aircraft,
a copy of the manufacturer’s production flight test
procedures and check-off list;
(d) for a product other than a Class II or Class III product referred to
in subregulation 21.133 (2B), an outline of the materials review
system, the procedure for recording decisions of the Materials
Review Board and for disposing of rejected parts;
(e) an outline of a system for informing company inspectors of
current changes in engineering drawings, specifications, and
quality system procedures.
Civil Aviation Safety Regulations 1998 (CASR)
Office of Legal Counsel CASR – 1st Edition – January 2003
Civil Aviation Safety Authority Replacement Page – Amdt No. 5: Effective 27 November 2003
Part 21 — 58
(f) a list or chart showing the location and type of inspection
stations.
Note A Materials Review Board must be established by the holder of a production
certificate: see regulation 21.145.
(1B) CASA must approve a manual that is prepared for, and meets the
requirements of, this regulation.
(2) The holder of a production certificate must, on the request of CASA,
make available to CASA information regarding all delegation of
authority to suppliers to make major inspections of parts or
assemblies for which the holder is responsible.
Penalty: 25 penalty units.
(3) An offence against subregulation (2) is an offence of strict liability.
Note For strict liability, see section 6.1 of the Criminal Code.
Source FARs section 21.143 modified.
21.144 Production inspection system
The production inspection system mentioned in paragraph
21.143 (1A) (c) must provide for the following:
(a) properly identifying incoming materials, and bought or
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：澳大利亞CASR Civil Aviation Safety Regulations上(70)