曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

inHg. If necessary, adjust the system.
(9) Install the instrument panel cover. Refer to Section 25-10.
AIRCRAFT
Vacuum DA 40 Series
AMM
Page 204
20 Sep 2007 37-00-00 Doc # 6.02.01
Rev. 5
4. Adjust the Vacuum Regulator
WARNING: DO NOT USE METAL TOOLS THAT CAN TOUCH THE ELECTRICAL
CONNECTIONS ON THE INSTRUMENT PANEL FLOOR.
Detail Steps/Work Items Key Items/References
(1) Remove the instrument panel cover. Refer to Section 25-10.
(2) Do an engine run-up. Refer to Section 71-01.
(3) Make a note of the vacuum value.
(4) If necessary, adjust the vacuum regulator:
S Bend the lock-tabs away from the T-bar.
S Turn the T-bar to adjust the vacuum.
S Bend the lock-tabs to lock the T-bar.
The vacuum must be 4.8 - 5.4 inHg at
1800 RPM.
On the bottom of the regulator.
Monitor the vacuum value.
(5) Shut down the engine.
(6) Install the instrument panel cover. Refer to Section 25-10.
AIRCRAFT
DA 40 Series
AMM
Vacuum
Doc # 6.02.01
Rev. 5 37-00-00 Page 205
20 Sep 2007
5. Remove/Install the Suction Gauge
A. Remove the Suction Gauge
Detail Steps/Work Items Key Items/References
(1) Remove the instrument panel cover. Refer to Section 25-10.
(2) Release the flexible hose to the vacuum gauge. Refer to Figure 2.
Put a cap on the hose end.
(3) Remove the bezel nut that attaches the gauge to
the instrument panel.
(4) Remove the gauge from the instrument panel.
B. Install the Suction Gauge
Detail Steps/Work Items Key Items/References
(1) Put the vacuum gauge in position in the
instrument panel.
Refer to Figure 2.
(2) Install the bezel nut that attaches the gauge.
(3) Connect the flexible hose to the vacuum gauge.
(4) Install the instrument panel cover. Refer to Section 25-10.
(5) Do an engine run-up. Refer to Section 71-01.
Do a test for correct operation of the
vacuum system. If necessary, adjust
the system.
AIRCRAFT
Vacuum DA 40 Series
AMM
Page 206
20 Sep 2007 37-00-00 Doc # 6.02.01
Rev. 5
Intentionally left blank
AIRCRAFT
DA 40 Series
AMM
Standard Practices and
Structures
Doc # 6.02.01
Rev. 5 51-TITLE Page 1
20 Sep 2007
CHAPTER 51
STANDARD PRACTICES AND
STRUCTURES
AIRCRAFT
Standard Practices and
Structures
DA 40 Series
AMM
Page 2
20 Sep 2007 51-TITLE Doc # 6.02.01
Rev. 5
Intentionally left blank
AIRCRAFT
DA 40 Series
AMM
Standard Practices and
Structures
Doc # 6.02.01
Rev. 5 51-CONTENTS Page 1
20 Sep 2007
TABLE OF CONTENTS
CHAPTER 51
STANDARD PRACTICES AND STRUCTURE
1. General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
2. Types of Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
3. Laminated Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
4. Sandwich Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
5. Bonded Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
6. Repair Limitations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Section 51-10
Investigation
1. General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
2. Damage Classification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
3. Types of Damage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
4. Inspection Techniques . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
5. Further Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
AIRCRAFT
Standard Practices and
Structures
DA 40 Series
AMM
Page 2
20 Sep 2007 51-CONTENTS Doc # 6.02.01
Rev. 5
Section 51-20
Repair Processes
1. General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
2. Center of Gravity Limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
3. Control Surface Balancing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
4. Drain/Vent Holes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
5. Holding the Component . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
6. Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
7. Workshop Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：鉆石40系列AMM 2(107)