曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

the steering lines function in the same manner.) The
main steering lines divide into various smaller lines,
which attach to multiple points on the trialing edge of
the wing. Pushing on either one of the steering bars
causes the steering lines to pull down the corresponding
surface of the trailing edge on the wing, creating
drag. This in turn slows that side of the wing and
banks the PPC into a turn.
Pushing both steering bars simultaneously causes
the steering lines to pull down equally on the trailing
edge, which causes two things to happen: it decreases
the powered parachute’s forward speed by increasing
the drag and it changes the shape of the wing,
Figure 3-8. Steering bars are located just aft of the
nosewheel and mounted on each side of the aircraft.
increasing angle of attack which increases lift. This
procedure, called “flaring” or “braking the wing” allows
the pilot to touch down at a slower rate of speed
and descent, thus creating a smoother landing, which
results in less wear and tear on the aircraft as a whole.
[Figure 3-9]
Figure 3-9. Steering lines are divided into two sections; a
single heavy line is attached to the steering bars.
Wings and Components
The powered parachute wing is unique, as compared
to a fabric wing on an airplane, in that when it is not
inflated it loses its ability to produce lift. When a
powered parachute wing is inflated or pressurized, it
becomes semi-rigid and is capable of producing lift
and supporting a load. Rather than being bolted to the
fuselage like an airplane, the parachute wing is attached
to the cart by lines and cables which are known
as risers.
The wings are manufactured by attaching an upper
and lower section of skin to ribs. [Figure 3-10] The
ribs of the wing determine the airfoil shape. [Figure
3-11] The shape of a powered parachute wing
will change slightly when faced with different gross
weights, air pressures, and environmental conditions
such as moisture, air temperature and wind.
Different wing manufacturers use different fabric
treatments to render the fabric airtight, so the air that
enters the wing cannot escape through the fabric surface.
The top surface of the wing is generally treated
to help protect it from ultraviolet light and the elements.
Keeping the powered parachute wing out of
direct sunlight will increase its useful life.
If the fabric degrades and air is allowed to escape
through pores of the cloth, the overall flight performance
of the wing is greatly reduced. If your pow3-
6
ered parachute wing should become too porous, more
groundspeed may be needed to pressurize the wing,
takeoff distance may increase, more RPM may be
required to hold altitude, and fuel consumption may
increase.
At first sight, the suspension lines on the powered
parachute wing might appear like an unorganized wad
of strings. On the contrary, each line has a distinct
purpose and each line has distinct properties. The suspension
lines are sometimes designated A through D
and differ between manufacturers; check your POH to
know the line labels for your PPC. [Figure 3-12] The
front suspension lines are located at the leading edge
and the steering lines connect to the trailing edge. The
Figure 3-11. Airflow into the wing.
Figure 3-12. Front and rear suspension lines.
Figure 3-10. Canopy cross-section.
suspension lines come together at a point where they
connect with the riser. (The risers are the connection
between the suspension lines and the cart.) Many
manufacturers color-code the wing suspension lines
to assist the pilot in their preflight inspection and layout
of the wing prior to inflation. [Figure 3-12]
Suspension lines must be constructed of very strong
materials, yet remain very small in profile to reduce
parasite drag. The most commonly used materials are
polyaramid and polyethelene, which are both carbon
based.
Kevlar® is a common polyaramid used for suspension
lines. Its properties render it extremely strong, as well
as resistant to stretching or shrinking, and it is not susceptible
to temperature changes. However, one critical
drawback of polyaramids is that they tend to kink
or knot when looped around. When polyaramids are
used to construct suspension lines, they are encased in
a skin of a terylene product, like Dacron® or a product
with similar properties. Polyethelene materials, such
as Spectra®, Dyneema® or Technora®, are very strong
as well as more flexible than polyaramids, which
makes them more durable under hard use. However,
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：Powered Parachute Flying Handbook動力傘飛行手冊(24)