曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

None
B. Removal
1) Open A / P circuit breaker.
2) Remove the access door located under L.H. wing 512.
3) Disconnect the connector (7).
4) Uncouple the rod (1) on crankpin (8). Retain the nut (4), washers (3) and the bolt (2). Discard the cotter
pin (5).
5) Hold the servo—actuator (6) and retain bolts (9), washers (10). Discard nuts (11).
6) Place the servo—actuator on a work bench.
C. Installation
1) Position the servo—actuator (6).
2) Secure the servo—actuator (6) with bolts (9), washers (3) and new nuts (11).
3) Secure the rod (1) to the crankpin (8) with the bolt (2), the washers (3), the nut (4). Lock with a new cotter
pin (5).
4) Connect the connector (7).
5) Install the access door 512.
6) Close A / P circuit breaker.
ABAB
Validity : CENTURY 21 22-11 Page 201
00 (AG) DEC 99
 

  1 — Rod
2 — Bolt
3 — Washer
4 — Nut
5 — Cotter pin
6 — Servo—actuator
7 — Connector
8 — Crankpin
9 — Bolt
10 — Washer
11 — Nut
12 — Setting nut

14221200AAA EWZ4000 

Servo—actuator — Removal / Installation
Figure 201
 
3. ADJUSTMENTS / TESTS — SERVO—ACTUATOR
A. Tools and consumable materials
— 2 seal retainers
— 2 protection shims
— 1 dynamometer
B. Tests on table
1) Install the servo—actuator on the work bench according to Detail A, Figure 202.
2) Uncouple the dynamometer.
3) Connect electrically according to Detail B, Figure 202.
4) Close "K" switch ; this actuates the engagement and the crankpin turns ; to reverse direction of rotation, tilt
5) Open "K" to stop ; attach the dynamometer to the crankpin hinge line.
6) Close "K".
7) Read the corresponding force on the dynamometer and compare it with Paragraph 3D.
8) Open "K".
9) Reset if necessary, then safety nut in position — refer to Paragraph 3C.
C. Setting of servo—actuator stress limiter
1) Remove the servo—actuator so as to test stress limiter on work bench — refer to Paragraph 2 B.
2) The stress limit is defined at the link. It must be measured with the dynamometer in the rotation plane of the hinge line. The pull direction must draw a 90° angle with the lever arm.
To change the adjustment, unpin the lockwasher, tighten to increase the stress limit value, untighten to decrease it.
CAUTION : AFTER SERVO—ACTUATOR STRESS LIMITER ADJUSTMENT, DO NOT FORGET TO SAFETY THE NUT WITH A COTTER PIN
THE NUT IS CONSIDERED SAFETIED ONLY AFTER ITS NOTCHES LINE UP WITH ONE OF THE BOLT PIN HOLES. FOR THIS, DO NOT HESITATE TO COMPLETELY REMOVE THE NUT SO AS TO ADD OR REMOVE ONE OR SEVERAL WASHERS IF NECESSARY
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：TB20 MAINTENANCE MANUAL 22 AUTO FLIGHT TB20飛機維護手冊 22 自動飛行(10)