曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

(2)  Put a 3/32 Allen wrench into the access hole for the locking screw. Engage the wrench into the screw.  Refer to Figure 1 (KLN 89B), Figure 2 (KLN 94), Figure 3 (MFD 150), Figure 4 (GNS 430), or Figure 5 (GNS 530). 
(3)  Turn the screw counter-clockwise until the unit disengages from the mounting rack. 
CAUTION: DO NOT PULL ON THE KNOBS. DO NOT PRY THE FACE-PLATE. YOU CAN DAMAGE THE UNIT. CAUTION: DO NOT TOUCH THE CONNECTOR CARD AT THE REAR OF THE UNIT. THE ELECTROSTATIC CHARGE ON YOUR BODY CAN DAMAGE THE UNIT. 
(4)  Pull gently on the sides of the unit to remove it from the mounting rack. 
(5)  Install the protective covers on the rear connectors of the unit. 

%

Doc # 6.02.01 Page 201
Rev. 4 09 Jan 2003

34-58-00
DA 40 Series
AMM

%

%
%

%
%
%

%
%
%

%
%

%
%

%
%

%
%

%

% B. Install the GPS Receiver %

Detail Steps/Work Items  Key Items/References 
(1)  Remove the protective covers from the connectors on the replacement unit. 
(2)  Slide the unit into the rack. Engage the locking screw so that the latch front-lobe touches the rack. 
(3)  Turn the locking screw clockwise so that the rear lobe engages the mounting rack.  Refer to Figure 1 (KLN 89B), Figure 2 (KLN 94), Figure 3 (MFD 150), Figure 4 (GNS 430), or Figure 5 (GNS 530). 
CAUTION: DO NOT OVER-TIGHTEN THE LOCKING SCREW. YOU CAN DAMAGE THE LOCKING MECHANISM. 
(4)  Continue to turn the screw until the unit is fully installed in the mounting rack. 
(5)  Close the related circuit-breaker(s).  GPS circuit breaker for KLN 89B, KLN 94, and MFD 150. COM and NAV/GPS circuit breakers for Garmin GNS 430/530. 
(6)  Do a test of the GPS.  Refer to Paragraph 6. 

%

Page 202 Doc # 6.02.01 09 Jan 2003 Rev. 4
34-58-00
Navigation
AMM

% 3. Remove/Install the GPS Annunciation Control Unit
%
%
%

%

%
%
%

%

% A. Remove the GPS Annunciation Control Unit %

Detail Steps/Work Items  Key Items/References 
(1)  Remove the instrument panel cover.  Refer to Section 25-10. 
(2)  Dis-connect the connector from the rear of the remote GPS annunciation control unit. 
(3)  Remove the screws which attach the GPS annunciation control unit to the panel.  Hold the GPS annunciation control unit! 
(4)  Remove the GPS annunciation control unit from the panel. 

% % % B. Install the GPS Annunciation Control Unit
%

%

%
%
%

%

%
%
%
%

Detail Steps/Work Items  Key Items/References 
(1)  Put the GPS annunciation control unit in position in the panel. 
(2)  Install the screws which attach the GPS annunciation control unit to the panel. 
(3)  Connect the connector to the rear of the GPS annunciation control unit. 
(4)  Install the instrument panel cover.  Refer to Section 25-10. 
(5)  Do a test of the GPS.  Refer to Paragraph 6. 

%

Doc # 6.02.01 Page 203
Rev. 4 09 Jan 2003

34-58-00
AMM

% 4. Remove/Install the GPS Annunciation Unit
%

%

%
%
%

%
%
%

% A. Remove the GPS Annunciation Unit %

Detail Steps/Work Items  Key Items/References 
(1)  Remove the instrument panel cover.  Refer to Section 25-10. 
(2)  Dis-connect the connector from the rear of the remote GPS annunciation unit. 
(3)  Remove the screws which attach the GPS annunciation unit to the panel.  Hold the GPS annunciation unit! 
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：鉆石40飛機維護手冊 DA 40 SERIES AMM 4(22)