(c)
Dimensional inspections are included for critical wear areas.   However, if visual inspection shows no indication of wear or damage, dimensional requirements shall be left to the judgment of the inspection personnel.

Inspection
Page 324 Apr 1/05 Copying, use or disclosure of information on this page is subject to proprietary restrictions.
20-00-02/70-00-01

Wide Band Roller Contact Pattern
Figure 313

Inspection

20-00-02/70-00-01

Polishing
Figure 314

Inspection

20-00-02/70-00-01

Unacceptable Cage Defects
Figure 315

Inspection

20-00-02/70-00-01

Cage Defects
Figure 316

Inspection
Page 328 Apr 1/05 Copying, use or disclosure of information on this page is subject to proprietary restrictions.
20-00-02/70-00-01

Cage Defects
Figure 317

Inspection

20-00-02/70-00-01

(8)  Prepare non-separable bearings for analyzer check as follows:
(a)  
Demagnetize bearings so residual magnetism does not exceed five gauss.

(b)  
Vapor degrease bearings. (SECTION II, Method No. 203B.)

WARNING: SOLVENT VAPORS ARE TOXIC AND FLAMMABLE.  DO NOT INHALE. OBSERVE FIRE PRECAUTIONS.

(c)  
Dip soak bearings in clean solvent (Federal Specification P-D-680, Type I).  Do not remove bearings from dip soak until ready for analyzer check.

WARNING: SOLVENT VAPORS ARE TOXIC AND FLAMMABLE.  DO NOT INHALE VAPORS. OBSERVE FIRE PRECAUTIONS.
CAUTION: DURING CLEANING, DO NOT PERMIT HIGH ROTATIONAL SPEEDS OF BEARINGS AS DAMAGE CAN RESULT.  SLOW ROTATIONAL SPEEDS ARE PERMISSIBLE.
(d)  
Remove bearing from dip soak. Spray bearing using solvent (Federal Specification P-D-680, Type I).

WARNING: USE CORRECT PERSONAL PROTECTION.  COMPRESSED AIR WILL CAUSE LOOSE PARTICLES THAT CAN GET IN YOUR EYES. COMPRESSED AIRFLOW CAN CAUSE CUTS, DO NOT POINT IT AT YOUR SKIN.

(e)  
Pressure air-dry (20 psig (137,895 kPa) maximum) parts until free of moisture.

(f)  
Lubricate bearing to be checked using filtered oil (MIL -L-6085) (SECTION VII).

(9)  Perform bearing analyzer check on non-separable bearings as follows:
NOTE:  The following procedures apply only when using Bearing Analyzer (Electronic Bearing Analyzer Model BA-20-3. (See Figure 318.)
(a)  
Obtain a Master Bearing from Bearing Inspection Inc., (SECTION VII).  Using the Master Bearing, calibrate the analyzer in accordance with manufacturer instructions.

(b)  
Install bearing to be inspected on analyzer in accordance with manufacturer’s instructions.

NOTE:  E PEAK to PEAK limits and RMS (Root Mean Squared) readings contained in overhaul manuals are measured using selector switch settings listed in Figure 318.

(c)  
Set switch selectors of Bearing Analyzer Model BA-20-3 per Figure 318.

Inspection
Page 330
Apr 1/05

20-00-02/70-00-01

SELECTOR SWITCH SETTINGS FOR ANALYZER OPERATION SET MILLIVOLTS FULL SCALE SELECTOR TO 1 SET MILLIVOLTS PER DIVISION SELECTOR TO 1 SET MILLISECONDS PER DIVISION SELECTOR TO 10
Bearing Analyzer Model BA-20-3
Figure 318

Inspection
Page 331
Apr 1/05

20-00-02/70-00-01
(d)
Perform analyzer check of bearing in accordance with manufacturer instructions.

NOTE:  Bearing shall conform to bearing analyzer inspection standards as specified in applicable manual for unit in work.

(e)  
If bearing was pre-oiled, clean bearing using vapor degreaser (SECTION II, Method No. 203B).

NOTE:  An asterisk is etched onto bearings receiving inspection during overhaul of an engine. Engine time since new to overhaul or overhaul bearings constitutes one cycle for the bearing. Repair engine bearings that are removed and inspected do not receive an asterisk.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：標準施工手冊 STANDARD PRACTICES MANUAL 20-00-02/70-00-01(48)