A. Main (continued)
NOTE: The shaded parts, time delay plunger (2), landing 12.
gear selector spool (19) and manifold (35) are
matched, lapped parts. It it is necessary to 47
replace any of these parts, replace them with a
matched assembly containing (2), (19) and (35). 13-
Shaded parts, transfer sleeve (7), and spool (10) 14.
are also matched and lapped parts and must be
replaced by a matched assembly containing (7)
and (10).
42
46

1.
TimeDelay Valve 17. Landing Gear Selector Spool 33. O-Ring

2.
Plunger, Time Delay 18. O-Ring 34. Fitting

3.
Spring 19. Spool, Landing Gear Selector

35. ManifoldAssembly

4.
O-Ring 20. O-Ring

36. Sleeve, Transfer

5.
Screw

21. HandleDetent Assembly 37. O-Ring

6.
TransferValve 22. O-Ring

38. O-Ring

7.
Sleeve,Transfer 23. Plunger

39. Backup

8.
O-Ring,Sleeve 24. O-Ring

40. Nut
25. Spring

9.
Door Selector Spool 41. Fitting

26. Retainer

10.
Spool, Door Selector

42. Bolt
27. O-Ring

11.
Door Solenoid Valve Assembly

43. Insulating Plate
28. Fitting

12.
Solenoid, Door

44. Switch Assembly

13.
O-Ring, Solenoid 29. O-Ring

45. Washer

14.
Spring,Plunger Return 30. Backup

46. Screw

15.
Plunger 31. Nut

16.
Pin 32. Fitting 47. Wire, Safety

48. Strap, Plastic
Power Pack Manifold
Figure 404

EFFECTIVITY:

040-999
29-10-00 Jan10/90
PIPER AIRCRAFT

PA-42-720 (Advanced Tralner)
MAINTENANCEMANUAL
A. Main (continued)
21.Disassemblyof Manifold. (Figure 404) (continued)
(f)
Removelanding gear handle-release

retainer, spring, and plunger from manifold. The plunger end has a ball which must remain in place.

(g)
Removecaps and fittings; wash manifoldin cleaning solvent (Federal Specification PS-661or equivalent)and dry with filtered, compressedair. Ensure internal passagesare clean. Reinstallcaps on fittings.

22.Assemblyof Manifold. (Figure 404)
(a)
Lubricateand install O-ring on landing gear selector spool. Install O-ring into manifold at opposite end.

NOTE: The landing gear selector spool, time delay valve plunger, and manifold are matched, lapped parts, and must be replaced as an assembly only.

(b)
Insert selector spool into manifold from landing gear handle end of manifold. Insert only until selector spool taper is protruding approximately0.06 inch out manifold end.

NOTE: If selector spool is not protruding approximately opposite
0.06inch out of manifold, rack, when installing into body (see Figure 405), gear will not engage in proper position. Do not move selector spool more than 0.12 inch out of manifold, opposite rack. The O-ring could get caught and damaged, necessitatingreplacement.
(c)
Ensure landing gear selector spool slides freely.

(d)
Ensure door solenoid spool moves freely within transfer sleeve.

NOTE: The spool and transfer sleeve are matched, lapped parts and must be replaced as an assembly only.

(e)
Lubricatefour O-rings and install on transfer sleeve.

(f)
Install transfer sleeve into manifold.

(g)
Attach plunger to door selector spool with pin and install into transfer sleeve.

1.Manifold
2.Gear
3.ReturnCam

Indexingof Selector Spool 
Figure405 
EFFECTIVITY: 
040-999 
PAGE16  29-1000 
Jan 10/90 

PIPERAIRCRAFT
PA-42-720(AdvancedTrainer)
MAINTENANCE MANUAL

A. Main (continued)
22.Assemblyof Manifold. (Figure 404) (continued)
(h)
LubricateO-ring(MS 28775-018) and install on solenoid.

(i)
Lubricatedoor solenoid threads, insert plunger return spring into plunger cavity, and screw assemblyinto manifold. Torque to 70 inch-pounds.

(j)
Install time delay plunger and spring into manifold.

(k)
LubricateO-ring,installonto screw, and mount time delay assembly into manifold. Screw must be flush with outside of manifold.

23. Installationof Manifold. (Figure 404)
(a)
LubricateO-rings and install on five transfer sleeves.

(b)
Insert transfer sleeves into manifold.

(c)
Mate manifold to power pack body, being sure not to damage O-rings on transfer sleeves.

NOTE: When mating manifold with power pack body, index landing gear selector spool rack with input shaft gear (Figure 405). With landing gear selector spool protruding 0.06 inch from face A of manifold and input shaft return cam in horizontal position, tooth of input shaft gear must match with tooth space in landing gear selector spool rack.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：夏延飛機維護手冊 Cheyenne IIIA PA-42-720 AMM 2