曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

(1.) With one inch masking tape, mask off leading edge boot area, following 1/2-inch margin for non-recessed boots. Ensure tape is masked accurately to eliminate cleaning off excesscement later.
(2.) Clean metal surfaces atleast twice with MEK or acetone. For final cleaning, wipeoff solventfilmquicklywith clean, dry cloth before it dries.
NOTE: If desired, reapply zinc chromate primerover bare leading edges. Whenhard, scuffsand chromate surfacesand clean beforeapplyingcement.
Deicerscan be installedon alodined or anodized surfaces.
(3.) Fill gaps of skin splices that leadunder deicers withsealingcompoundEC-801.
(4.) Removesump plugs from air connection grommets.Removesectionsof doped fabric usedto cover the air connection holes,if necessary. Draw out ends of non-kink hose sectionto protrude through connectionholesin leading edge. If hole is crackedor deteriorated,replacehose.
(b) Preparationof Deicer
Moistencleanclothwith MEK or acetone. Carefullycleanrough, back surfaceofboot at least twice. Change clothsfrequentlyto avoid recontamination areas.
of cleaned

(c) MountingDeiceronLeadingEdge
Thoroughlymix EC-1300L cementbeforeusing.Brush on one even coat to cleaned back surfaceof boot andto cleaned metal surface. Allowcementto air dry for a minimum 1 hour. Applysecondcoat to bothsurfacesand allow to air dry anotherhour.Keepambient installation temperaturebetween40° and 11 0°F. Longerdryingtime for cementcoats may be requiredas humidityapproaches99%. Deicer and leading edgecanbe cemented a maximum 48 hours beforeactualinstallationif cemented partsarecoveredandkeptclean. Snapa chalk linealong leading edgeof airfoil section.Darkenchalkline on leadingedgeand
whitereferencelineon boot with a ball pointpen. Most bootsaremade with excess materialat inboardand outboard edgesforfinal trimming afterinstallation.Some recessed bootstrim on upperand lower edges.
EFFECTIVITY: 040-999

JanJan 10/9010/90 30-10-00
PIPER AIRCRAFT
PA-42-720(Advanced Trainer)
MAINTENANCEMANUAL

A. Airfoil -Description and Operation (continued)
11. Installation (continued)
Usingclampsor safetywire, attach hose to deicerconnectionsas follows:
1.  
Holdingbacksideof boot close to leading edge, fastenend of each non-kink hose to correspondingairconnection stem. Usetinnermanor other suitable non-kink hose clamps. Tighteneachclamp using slip joint pliers. Do not over squeeze clamp, damaging

hose.

2.  
Pushhoseconnectionsinto either leading edgegrommetsor seals. (Limit handling cementedside of boot.) Reactivatecementalongcenterlineleadingedge surfaceand boot in spanwise strips,approximately6 inches wide. Rubber roll deicer firmlyagainst leadingedge,being careful notto trap air under deicer. Alwaysrollparallelto inflatable tubes. Positiondeicercenterlineto coincide with leading edgecenterline. Hold boot in positionwhile reactivatingabout3 inches around connections andcorrespondingholes in leadingedge, using a clean, lint-free cloth moistenedwith Toluol. Insert connections in leadingedge holes after cement has dried to a tacky state and rubber roll boot to leading edgeof tacky area.

3.  
Ifdeicerattachesoff line, use MEK to remove and repositionproperly.Avoid twisting or sharp bending of deicer.

4.  
Rubberroll, applying pressureover entire deicersurfaceparallel to inflatabletubes. Roll edges with narrow stitcher-roller.

CAUTION:  AVOID EXCESSIVE SOAKING OR RUBBING OF CEMENT, WHICH COULD REMOVECEMENTFROMSURFACE.

5.  
Removeall masking tape and clean surfaces carefully with MEK. Prevent solventfrom runningunder deicer edges.

6.  
Applymaskingtapeto deicer edges where exposed trimmedendsor gaps between sectionsmust be filled with MMM EC-801 sealingcompound.

7.  
Applymasking tape to deicerapproximately1/4-inch in fromtrailingedgesand to wing skin approximately1/4-inchfrom trailing edges,both forming a neat, straight line.

8.  
Apply brush coatof A-56-B cement to surfacesbetweentapesand to EC-801 seams. Ensureconductivecoating(A-56-B)is continuousfromdeicersurfaceto wing painted surface.

9.  
Removetape immediatelyafter applying A-56-Bcement(before cement dries).

10.  
Install flow strips ontoleadingedgeusing3M EC1300L cement asshownon Figure 3.

NOTE:  Applicationof A-56-Bconductivecement is not necessary on deicers containing CONDUCTIVElabels.
WARNING: CEMENTSAND SOLVENTS USED ARE FLAMMABLEANDTHEIRFUMES TOXIC. CONDUCTALL WORK IN A WELLVENTILATEDAREAAWAY FROMSPARKS OR FLAMES.(USEOF SOLVENTRESISTANTGLOVES
IS RECOMMENDED.)
If boots mustbe removed or loosened,useMEKto soften the adhesionline. Applya minimum of solvent to seam linewhile applying tensionto peel backboot. Remove slowenoughto allow solventto undercut cement preventingdamageto part. Avoid excessivequantitiesof solvent.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：夏延飛機維護手冊 Cheyenne IIIA PA-42-720 AMM 2(19)