Introduction Page 17 Revised: February 28, 2002
THE NEW PIPER AIRCRAFT, INC.
PA-44-180
AIRPLANE MAINTENANCE MANUAL
LIST OF ILLUSTRATIONS (cont)
FIGURE NO. SUBJECT GRID NO.
74-6. Installation of Bearings 3H17
74-7. Magneto Oil Seal Installation on T-125 Assembly Fixture 3H19
74-8. Magneto Internal Timing 3H19
74-9. Engine Timing Marks 3H21
74-10. Stipping Tool 3I2
74-11. Inserting Stipping Tool 3I2
74-12. Cutting Insulation 3I2
74-13. Removing Silicone Rubber from Wire 3I2
74-14. Installation of Plug Endnut 3I3
74-15. Flaring out the Shielding 3I3
74-16. Installation of Ferrule 3I3
74-17. Driving Tool 3I3
74-18. Insulation in Harness Cap 3I5
74-19. Securing Wire in Harness Cap 3I5
74-20. Installation of Electrode Screw 3I5
74-21. Installation of Insulator Sleeve 3I5
74-22. Installation of Spring 3I6
74-23. Removing Spark Plug Frozen to Bushing 3I6
74-24. Magneto and Starter Switches 3I9
77-1. Engine Instrument Lines Installation 3I15
77-2. Electric Tachometer Installation 3I19
77-3. Cylinder Head Temperature Gauge Calibration 3I22
78-1. Inspection of Mufflers 3J5
79-1. Oil Pressure Gauge Calibration 3J14
79-2. Oil Temperature Gauge Calibration 3J16
80-1. Exploded View of Gear Reduction Starter Motor 3K9
80-2. Turning Motor Commutator 3K12
80-3. Testing Motor Armature for Shorts 3K12
80-4. Testing Motor Fields for Grounds 3K12
80-5. No Load Test Hookup 3K12
80-6. Stall Torque Hookup 3K14
91-1. Tire Balancer Fixture 4B10
91-2. Control Surface Balancing Tool 4B21
91-3. Fabricated Aileron Bellcrank Rigging Tool 4B22
91-4. Fabricated Aileron and Flap Rigging Tool 4B23
91-5. Fabricated Stabilator Rigging Tool 4B24
91-6. Fabricated Rudder Rigging Tool 4B24
91-7 thru 91-30. Electrical Schematics 4C6
— Note —
Refer to Card 4 Grid No. 4C6 for Electrical Schematic Index
Introduction Page 18 Revised: February 28, 2002
1A22
THE NEW PIPER AIRCRAFT, INC.
PA-44-180
AIRPLANE MAINTENANCE MANUAL
LIST OF CHARTS
CHART NO. SUBJECT GRID NO.
401 Structural Inspection and Replacement 1B5
601 Leading Particulars and Principal Dimensions 1C19 1201 Thread Lubricants 1G11 2001 Maximum Distance Between Supports for Fluid Tubing 1G20 2101 Troubleshooting (Janitrol Heater) 1H6 2102 Blower System Wire Color Codes 1H11 2103 Inspection (Ignition Unit) 1I7 2401 Troubleshooting (Alternator) 1J16 2402 Troubleshooting (Battery) 1J21 2403 Alternator Belt Tension 1K1 2404 Hydrometer Reading and Battery Charge Percent 1K3 2701 Cable Tension Vs. Ambient Temperature 2B8 2702 Troubleshooting Control Surfaces 2B12 2801 Troubleshooting (Fuel System) 2E1 2802 Sender/Fuel Quantity Gauge Tolerances 2E16 2901 Leading Particulars, Hydraulic System 2F4 2902 Troubleshooting Hydraulic System 2F5 3201 Troubleshooting (Landing Gear) 2G14 3202 Toe-In, Toe-Out Correction 2H12 3401 Troubleshooting (Vertical Speed Indicator) 2K10 3402 Troubleshooting (Altimeter) 2K11 3403 Troubleshooting (Airspeed Tubes and Indicator) 2K12 3404 Troubleshooting (Magnetic Compass) 2K18 3701 Troubleshooting (Vacuum System) 2L11 3901 Troubleshooting (Annunciator Panel) 3B6 5101 List of Materials for Thermoplastic Repair 3C1 6101 Propeller Torque Limits 3F7 7101 Troubleshooting (Engine) 3F20 7301 Fuel Pressure Sender Test Specifications 3H3 7302 Troubleshooting (Fuel Pressure Gauge) 3H4 7401 Troubleshooting (Magneto) 3H10 7402 Coupling Torque 3I8 7701 Manifold Pressure Indicator (Troubleshooting) 3I17 7702 Tachometer (Troubleshooting) 3I18 7703 Cylinder Head Temperature (Troubleshooting) 3I21 7704 Exhaust Gas Temperature (Troubleshooting) 3I23 7901 Oil Pressure Sender Test Specifications 3J12 7902 Oil Pressure Gauge (Troubleshooting) 3J13 7903 Oil Temperature Indicators (Troubleshooting) 3J15 8001 Troubleshooting (Starter) 3K5 8002 Starting Motor Specifications 3K14
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：西門諾爾飛機維護手冊 simenole PA-44-180 AMM 1(7)
