12.
Check carburetor throttle body attaching screws for tightness; the correct torque for these screws are 40 to 50 inch-pounds.

5-20-00 Page 5-22 Revised: February 28, 2002
THE NEW PIPER AIRCRAFT, INC.
PA-44-180
AIRPLANE MAINTENANCE MANUAL

SCHEDULED MAINTENANCE CHECKS (CONT)
NOTES (CONT):
13.
Check landing gear system in accordance with instructions given in Chapter 32.

14.
A.  Overhaul or replace Hartzell propellers each five or six years or each 2000 or 2400 hours. (Refer to latest revision of Hartzell Service Letter No. 61 to determine specific requirements for individual airplanes.)

B.  Overhaul or replace Hartzell propeller governors each 2000 hours or at engine overhaul. (Verify TBO in latest revision of Hartzell Service Letter No. 61.)

15.
After 10 years time-in-service, pressurize all fluid hoses in fuselage and wing areas to system operating pressure and visually check for leaks. Hoses that pass inspection may remain in service and checked thereafter each five years time-in-service.

16.
Replace fuel tank vent line flexible connections as required, but not to exceed 7 years, 1000 hours, or fuel tank removal, whichever comes first.

17.
When using alternate fuels, refer to latest revision Lycoming Service Letter No. L185 for additional information and service procedures.

18.
For information on changing propeller spinner dome attaching locknuts, refer to latest revision Hartzell Service Instruction No. 118.

19.
Refer to Pilot's Operating Handbook for preflight and flight check, for intended function in all modes.

20.
Check at each annual or 100 hour inspection, whichever comes first. Refer to Chapter 52 for test procedures.

21.
Examine cables for broken strands by wiping the cable with a cloth along the length of the cable. Visually inspect the cable thoroughly for damage not detected by the cloth. Replace damaged cables. Refer to Advisory Circular 43.13-1(latest revision), Paragraph 198.

22.
Replace (or overhaul, if applicable) at engine overhaul or 5 years time-in-service, whichever comes first.

23.
In S/N’s 4496001 thru 4496015 only, verify compliance with Piper Service Bulletin No. 1016, latest revision.

24.
In S/N’s 4496001 thru 4496019 only, verify compliance with Piper Service Bulletin No. 1020, latest revision.

25.
In S/N’s 4496001 thru 4496019 only, verify compliance with Piper Service Bulletin No. 1023, latest revision.

26.
In S/N’s 4496001 thru 4496020 only, verify compliance with Piper Service Bulletin No. 1026, latest revision.

27.
In S/N’s 4496001 thru 4496015 only, verify compliance with Piper Service Bulletin No. 1028, latest revision.

28.
In S/N’s 4496001 thru 4496025 only, verify compliance with Piper Service Bulletin No. 1033, latest revision.

29.
In S/N’s 4496001 thru 4496028, and 4496031 only, verify compliance with Piper Service Bulletin No. 1040.

30.
In S/N’s 4496001 thru 4496036, verify compliance with Piper Service Bulletin No. 1041, latest revision.

31.
In S/N’s 4496001and up, verify compliance with Piper Service Bulletin No. 1048, latest revision.

32.
For new airplanes, at the first 100 hour inspection, while the airplane is on jacks, retorque the engine mount-to-fuselage bolts.

Page 5-23 Revised: February 28, 2002
1C5
THE NEW PIPER AIRCRAFT, INC.
PA-44-180
AIRPLANE MAINTENANCE MANUAL

SCHEDULED MAINTENANCE CHECKS (CONT)
NOTES (CONT):
33.
For airplanes 15 years old or older, using a 10X magnifier, visually inspect the entire surface of each cable terminal, turnbuckle, or other cable fitting for corrosion or cracking. Any evidence of corrosion or cracking, however minute, is cause for replacement. A logbook entry documenting the replacement of a cable terminal, turnbuckle, or other cable fitting relieves the inspection requirement for that fitting only, until such time as that fitting has been in service for 15 years.

34.
For aircraft in normal operation, each 7 years; or, for aircraft in training operations, each 2000 hours time-in-service: remove interior panels and headliner and conduct detailed inspection of aircraft structure (skin, bulkheads, stringers, etc.) for condition and security. Inspection of structure concealed by headliner may be accomplished by alternate means (i.e. - through the use of a borescope) without removing the headliner, providing access is obtained to all concealed areas and borescope provides sufficient detail to adequately accomplish the inspection.

35.
Inspect seat belt and shoulder harness ends and attachment points for condition and security. Inspect harness web material for condition and wear over its entire length. Particularly look for wear and fraying where harness web passes in and out of adjustable buckle end and shoulder harness inertial reel. If excessively worn, replace. In S/N’s 4496001 thru 4496035 only, inspect shoulder harness keeper nylon bushing on the lap belt. If excessively worn or missing, replacement of that half of the lap belt is required.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：西門諾爾飛機維護手冊 simenole PA-44-180 AMM 1(18)