曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

 (5)  S 012-006To open the ADL front cover, pull at the top edge.
 (6)  S 862-007Push the eject button on the ADL. (a) If a plastic protective disk is ejected from the disk drive, then remove it.
 (7)  S 862-008Close this circuit breaker: (a) On the P11 panel: 1) 11F23, DATA LOADER
 (8)  S 862-009Wait until all the status lights are off.
 NOTE:____ The status lights will flash on and off while the ADL does a self test.
 (9)  S 862-010Make sure that the circuit breakers are closed for the applicable component or system that will receive the new software.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 20-15-11
 ALL  ú ú 01 Page 210 ú Jan 28/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A

757
MAINTENANCE MANUAL

 S 422-012
 (10) Do these steps at the ADL to install the software:
 NOTE: You must know the correct software part numbers for the
____ component. For the component to be an approved installation, software with the correct part numbers must be installed.
 NOTE: This is a general procedure for software installation.
____ Some components have other steps that are necessary. The software installation task for the component will include all necessary steps.
 (a)  
Set the switch or switches on the data loader control panel to the applicable position for your component or system.

 (b)  
Carefully push the first disk (label up) into the disk drive.

 NOTE: If the destination component is active, the
____ installation sequence will begin and the RDY light will come on. When the data transfer begins, the PROG light will come on. The RDY light can flash when the component validates the data. If the software is on more than one disk, the CHNG light will come on when it is time to put in the subsequent disk.
 (c)  If the CHNG light comes on, wait approximately 10 seconds and then push the eject button.
 NOTE: The installation can fail if you wait too long
____ before you remove and install disks.
 1) Remove the disk from the disk drive. 2) Put the subsequent disk into the disk drive. 3) If there are more than two disks for the software
 installation, then remove and install disks until the COMP light shows.
 (d)  
When the COMP light comes on, wait approximately 10 seconds and then push the eject button.

 (e)  
Remove the disk from the disk drive.

 (f)  
If there was a plastic protective disk in the disk drive before you installed software, then put it back into the disk drive.

 S 862-013
 (11)
 Set the system select switch on the data loader control panel to the NORMAL position.

 (12)
 Close the front cover on the ADL.

 S 412-014
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 20-15-11
 ALL  ú ú 01 Page 211 ú Sep 28/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
757 MAINTENANCE MANUAL
 S 742-015
 (13) Make sure that the correct software part numbers are installed in the component.
 NOTE: The software installation task for the component has the
____ steps to do a software configuration check.
 S 862-044
 (14) Remove electrical power (AMM 24-22-00/201).
 D. Teledyne Airborne Data Loader Procedure
 S 862-042
 (1)  Supply electrical power (AMM 24-22-00/201).
 (a)  Make sure that the power is not removed while you install software.
 NOTE: A power interruption will cause a failure of the
____
 software installation.

 S 862-017
 (2)  
Make sure that the system select switch on the data loader control panel (P61) is set to the NORMAL position.

 S 862-018

 (3)  
Open this circuit breaker:

 (a)  On the overhead circuit breaker panel, P11:
 1) 11F23, DATA LOADER

 S 012-019
 (4)  
To open the ADL front cover, turn the cover knob clockwise and pull.

 S 862-020

 (5)  
Push the eject button on the ADL.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：757 AMM 飛機維護手冊 STANDARD PRACTICES - AIRFRAME(94)