WARNING:_______DO NOT SPRAY SOLVENTS. DO NOT KEEP SOLVENTS IN OPEN CONTAINERS. DO NOT USE FLAMMABLE SOLVENTS IN AIRPLANE. SOLVENTS AND CLEANERS CONTAIN TOXIC INGREDIENTS. WEAR PROTECTIVE GLOVES WHEN YOU USE THEM. DO NOT GET SOLVENT OR CLEANER ON YOUR SKIN OR EYES. MAKE SURE YOU HAVE SUFFICIENT VENTILATION OR USE RESPIRATOR MASKS.
 CAUTION:_______DO NOT USE SOLVENTS OTHER THAN THOSE SPECIFIED. THEY CAN CAUSE DAMAGE TO THE FINISH.
 (b)  Use the applicable solvent as follows:
 WARNING: DO NOT GET SOLVENTS IN YOUR MOUTH, OR YOUR EYES, OR
_______ ON YOUR SKIN. DO NOT BREATHE THE FUMES FROM SOLVENTS. SOLVENTS ARE HAZARDOUS MATERIALS. REFER TO PRODUCT MATERIAL SAFETY DATA SHEETS (MSDS) AND LOCAL REQUIREMENTS FOR PROPER HANDLING PROCEDURES.
 1) For tedlar, teflon, and solvent resistant finishes only,
 use solvent, Series 98 (AMM 20-30-98/201). 2) For acrylic surfaces, use naphtha, TT-N-95, Type II. 3) For all other surfaces and for hydraulic fluid
 contamination, use BMS 3-2.
 (c)  Use a polyethylene bottle to apply the solvent to the work surface or to a clean wiper.
 NOTE: Do not put wiper into the solvent container.
____
 (d)  
Rub the surface with force with a wiper or soft brush.

 (e)  
Flush the surface with clean solvent. Use clean wipers.

 (f)  
To remove excess solvent, let surface drain then rub dry.

 S 114-005
 (4)  Do these steps to clean the surface again:
 (a)  Apply solvent to a clean wiper.
 NOTE: Do not put the wiper into the solvent container.
____
 (b)  Rub the surface with the solvent-soaked wiper. Immediately rub dry with a clean, dry wiper.
 NOTE: Do not let the solvent dry by air. Replace
____Rub dry. the dirty wiper frequently with a clean one.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 20-10-15
 ALL  ú ú 01 Page 403 ú Sep 28/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
757 MAINTENANCE MANUAL
 (c)  Repeat the last two steps until the wiper shows no dirt.
 NOTE: If the prepared surface becomes dirty with dust, dirt,
____ grease, grit, or other contaminates, clean again as specified in this procedure.
 S 114-006
 (5) For plastic laminates and painted surfaces only, do these steps:
 (a)  Clean, if necessary, as specified in this procedure.
 CAUTION: DO NOT SAND THE PAINTED SURFACE AROUND THE DECAL EDGE IF
_______ CLEAR HYDRAULIC FLUID RESISTANT COATING WAS USED AS EDGE SEALER FOR THE DECAL. YOU CAN BREAK THE EDGE SEAL.
 (b)  
Lightly sand the surface with 280-grit or finer abrasive paper.

 (c)  
Clean again as specified in this procedure.

 F.  Apply Stencil Markings
 S 214-007
 (1)  
Make sure all stencil cuts are sharp and free of burrs.

 S 434-008

 (2)  
Attach the stencil tightly to the surface to prevent paint
 penetration under the edges.

 S 374-009

 (3)  
To paint the stencil marking, use the paint applicable to the surface finish as follows:

 (a)  If you use BMS 10-60, Type II Enamel or BMS 10-79, Type II Primer, refer to Decorative Exterior Finishes for preparation instructions (AMM 51-21-10/701).
 WARNING: STORE EC 942 IN A OPEN CONTAINER TO PREVENT CONCENTRATION
_______ OF FLAMMABLE HYDROGEN GAS. EC 942 CHEMICALLY REACTS WITH METAL CONTAINERS AND FREES FLAMMABLE HYDROGEN GAS.
 (b)  If you use EC 942 Black (Corogard 12), do these steps: 1) Mix thoroughly.
 CAUTION: DO NOT ADD MORE THINNER THAN A QUANTITY EQUAL TO
_______ ONE-FIFTH OF THE BASE MATERIAL.
 2)  Thin the base material with mixture (by volume) of 5/8 methyl isobutyl ketone and 3/8 butyl acetate.
 NOTE: You can use this material for up to 16 hours after
____ you thin it (pot life is 16 hours).
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 20-10-15
 ALL  ú ú 01 Page 404 ú Sep 28/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A

757
MAINTENANCE MANUAL
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：757 AMM 飛機維護手冊 STANDARD PRACTICES - AIRFRAME(65)