曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

 WARNING:_______THE CARGO FLOOR PANEL IS HEAVY. TO PREVENT INJURY, TWO PEOPLE ARE REQUIRED WHEN LIFTING OR MOVING THE CARGO FLOOR PANEL.
 CAUTION: DO NOT PUSH OR PULL THE CARGO FLOOR PANEL ACROSS THE FLOOR
_______ BEAMS. THIS ACTION CAN CAUSE DAMAGE TO THE BLANKET MATERIAL.
 (b)  Carefully remove the cargo floor panel.
 S 014-018
 (3)  Do this task to remove the left WXR R/T from the E5 rack: Weather Radar Receiver/Transmitter Removal (AMM 34-43-02/401).
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 34-43-05
 ALL  ú ú 05A Page 407 ú Feb 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 014-019
 (4)  
Do this task to remove the right WXR R/T from the E5 rack: Weather Radar Receiver/Transmitter Installation (AMM 34-43-02/401).

 S 024-020

 (5)  
Remove the left and/or the right R/T mount:

 (a)  
Disconnect the electrical connector DB139 from the blower assesmbly.

 (b)  
Put dust caps on the disconnected blower assembly connctors.

 (c)  
Remove the four screws, washers and a gasket that attach the left and right feeder waveguide to the R/T mount waveguide.

 (d)  
Left R/T mounts:

 

 1)  Remove all ground wires from ground terminal GDB138 on the R/T mount using an insertion/extraction tool. (WDM 20-20-11)
 NOTE: Use the insertion/extraction tool for a Burndy
____ terminal block with part number YHLZG8-1.
 2) Remove the two top and two bottom screws,nuts and washers that attach connector DB138 to the R/T mount. 3) Carefully remove connector DB138 from the R/T mount.
 (e)  Right R/T mount:
 1)  Remove all ground wires from ground terminal GDB140 on the R/T mount using an insertion/extraction tool. (WDM 20-20-11)
 NOTE: Use the insertion/extraction tool for a Burndy
____ terminal block with part number YHLZG8-1.
 2) Remove the two top and two bottom screws,nuts and washers that attach connector DB140 to the R/T mount. 3) Carefully remove connector DB140 from the R/T mount.
 (f)  Remove the four screws, washers and nuts which attach the R/T mount to the E5( ) shelf assembly.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 34-43-05
 ALL  ú ú 04A Page 408 ú Feb 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 (g)  Remove the R/T mount from the E5 shelf assembly.
 S 024-067
 (6)  
Put a cover over connector DB138 or DB140 that is lint free for protection of the electrical and waveguide section.

 S 024-068

 (7)  
Put a dust cap on the feeder waveguide.

 TASK 34-43-05-404-023
 4.  PASSENGER AIRPLANES; Weather Radar R/T Mount Installation (Fig. 401)
____________________________________
 A.  General
 (1)  The R/T mount (B139) is attached to the E30-1 upper shelf on the E30 equipment rack (E30 rack). The E30 rack is in the right crawlway forward of the main equipment center. To install the R/T mount, you must electrically and mechanically connect it to the E30 rack.
 B.  Special Tools and Equipment
 NOTE: Use the correct insertion/extraction tool fround in one of the two
____ crimp tool kits shown below. See crimp tool kit connector index.
 (1)  
Graphic Datakits International, Burndy P/N J1276-1
 Insertion/Extraction Tool

 (2)  
Daniels Mfg. Corporation, Astro P/N ATB3062-2
 Insertion/Extraction tool.

 

 C.  References
 (1)  
AMM 06-09-01/201 Body Section 41 Access Doors and Panels

 (2)  
AMM 24-22-00/201, Manual Control

 (3)  
AMM 24-29-01/401, Main Static Inverter

 (4)  
AMM 34-43-02/401, Weather Radar Receiver/Transmitter

 (5)  
AIPC 34-43-02 Fig. 1

 (6)  
SWPM 20-20-11

 D.  Access
 (1)  Location Zone 116 Area Between Nose Gear Well and Fuselage, RH
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 導航 NAVIGATION 2(145)