S 014-005

 (3)  
Do this task to remove the left WXR R/T from the E30 rack: Weather Radar Receiver/Transmitter Removal (AMM 34-43-02/401).

 S 014-006

 (4)  
Do this task to remove the right WXR R/T from the E30 rack: Weather Radar Receiver/Transmitter Installation (AMM 34-43-02/401).

 S 014-007

 (5)  
Do this task to remove the main static inverter from the E30 rack: Main Static Inverter Installation (AMM 24-29-01/401).

 S 024-009

 (6)  
Remove the R/T mount:

 (a) Disconnect the air hose clamps attached to the R/T mount.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 34-43-05
 ALL  ú ú 01A Page 402 ú Feb 10/94
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

 (b)  Remove the air hose from the right air inlet on the R/T mount.
 (c)  Remove the air hose from the left air inlet on the R/T mount.
 (d)  Disconnect the electrical connector DB139 from the waveguide
 switch.
 (e)  Disconnect all ten electrical connectors on the AEO 302
 disconnect panel connected to the R/T mount.
 (f)  Remove the four screws, washers and a gasket that attach the
 waveguide section 5 to the waveguide switch.
 (g)  Remove the six screws and locknuts that connect the E30-1 upper

 shelf to the E30 rack.
 CAUTION: BE CAREFUL TO PREVENT ACCIDENTAL DAMAGE TO THE WIRE
_______ BUNDLES ON THE E30-1 UPPER SHELF. WHEN YOU REMOVE THE E30-1 UPPER SHELF FROM THE E30 RACK, DAMAGE TO THE WIRES CAN OCCUR.
 (h)  
Carefully remove the E30-1 upper shelf from the E30 rack.

 (i)  
Remove the four screws and washers and a gasket from the right feeder waveguide at the waveguide switch.

 (j)  
Remove the four screws and washers and a gasket from the right feeder waveguide at the R/T mount.

 (k)  
Remove the right feeder waveguide.

 (l)  
Remove the four screws and washers and a gasket from the left feeder waveguide at the waveguide switch.

 (m)  
Remove the four screws and washers and a gasket from the left feeder waveguide at the R/T mount.

 (n)  
Remove the left feeder waveguide.

 (o)  
Remove all ground wires from ground terminal GD138 on the R/T mount using an insertion/extraction tool. (SWPM 20-20-11)

 NOTE: Use the insertion/extraction tool for a Burndy terminal
____ block with part number YHLZG8-1.
 (p)  Remove all ground wires from ground terminal GD140 on the R/T mount using an insertion/extraction tool. (SWPM 20-20-11)
 NOTE: Use the insertion/extraction tool for a Burndy terminal
____ block with part number YHLZG8-1.
 (q)  
Remove the two top and two bottom screws,nuts and washers that attach connector DB138 to the R/T mount.

 (r)  
Carefully remove connector DB138 from the R/T mount.

 (s)  
Remove the two top and two bottom screws,nuts and washers that attach connector DB140 to the R/T mount.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 34-43-05
 ALL  ú ú 01A Page 403 ú Feb 10/94
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 (t)  
Carefully remove connector DB140 from the R/T mount.

 (u)  
Identify connectors DB138 and DB140 for installation.

 (v)  
Remove the eight screws, washers and nuts which attach the R/T mount to the E30-1 upper shelf.

 S 024-062
 (7)  
Put a cover on the waveguide switch that is lint free for protection of the waveguide flanges and electrical connector.

 S 024-063

 (8)  
Put a dust cap on waveguide section 5.

 S 024-064

 (9)  
Put a cover over connector DB138 that is lint free for protection of the electrical and waveguide sections.

 S 024-065

 (10)
 Put a cover on connector DB140 that is lint free for protection of the electrical and waveguide sections.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 導航 NAVIGATION 2(143)