27-61-04
ALL ú ú 03 Page 203 ú Jun 10/94
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
TRAILING EDGE BEAM PISTON INBOARD FLIGHT
25. CAP
C-C
NOTE: THE AIRPLANE MUST BE SUPPORTED ON ITS LANDING GEAR WHEN YOU MEASURE THIS CLEARANCE.
THE SPOILER PANELS ARE NOT FLAT. MEASURE THE CLEARANCE
AT THE NEAREST POINT. THERE IS NO MAXIMUM CLEARANCE
BECAUSE OTHER PARTS OF THE PANEL CAN HAVE A GREATER
CLEARANCE.
1
Inboard Flight Spoiler Control Package Installation
Figure 201 (Sheet 2)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-61-04
ALL ú ú 01 Page 204 ú Oct 10/93
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
C79478
A
747-400 MAINTENANCE MANUAL
S 492-006
(5)
Install the spoiler actuator locking tool. S 862-007
(6)
Do this task to depressurize hydraulic systems No. 1 and 4: "Hydraulic System Depressurization" (AMM 29-11-00/201).
S 862-009
(7)
Do this task: "Supply Electrical Power" (AMM 24-22-00/201).
S 862-010
(8)
Put the FLT CONTROL HYD POWER - WING system 4 switch on the pilots' overhead panel, P5, to the SHUTOFF position.
S 862-011
(9)
Open these circuit breakers and attach DO-NOT-CLOSE tags:
(a)
P180, DC Power Distribution Panel 1) 180E22, LATERAL CONT VLV SYS 4
WARNING:_______ DO NOT PUT A PART OF YOUR BODY BETWEEN THE SPOILER AND THE WING
UNLESS THE SPOILER ACTUATOR IS LOCKED OR THE HYDRAULIC POWER IS
RELEASED. THIS CAN CAUSE INJURY TO PERSONS.
S 012-012
(10)
Open the wing access panel below the spoiler control package (572FB, left wing; 672FB, right wing).
S 022-013
(11)
Remove the spoiler control package:
(a)
Remove the bolt (14), washer (17), and nut (16) to disconnect the control package (1) piston rod end from the spoiler.
(b)
Remove the bushings (15) from the spoiler.
(c)
Remove the bolt (18), washers (11), and nut (13) to remove the antirotation plate (12) if it is necessary.
(d)
Put a container below the spoiler control package to catch the hydraulic fluid.
(e)
Disconnect the hydraulic lines (2) from the control package.
(f)
Install the caps on the hydraulic lines and in the ports of the control package.
CAUTION: YOU MUST NOT CHANGE THE LENGTH OF THE INPUT ARM ROD WHILE
_______ IT IS DISCONNECTED. YOU CAN CAUSE DAMAGE TO EQUIPMENT.
(g)
Remove the bolt (8), washers (10), and nut (9) to disconnect the control rod (6) from the input arm of the control package.
(h)
Remove the four mounting bolts (3), washers (4), and nuts (5) to remove the control package.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-61-04
ALL ú ú 01 Page 205 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
TASK 27-61-04-402-014
3. Spoiler Control Package Installation (Fig. 201)
____________________________________
A. Special Tools and Equipment
(1)
G27001-1, No. 5 and No. 8 Spoiler Actuator Locking Tool
(2)
MIT69B82662-17, Inboard Spoiler Socket Adapter Assembly
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 6(68)
