(f)
Move speed brake control lever to DN. All spoilers will fully retract.
(2)
Automatic Speed Brake Operation
(a)
Provide electrical power (Ref 24-22-00/201).
WARNING: BEFORE PROVIDING HYDRAULIC POWER, CHECK THAT PERSONNEL AND
_______ EQUIPMENT ARE CLEAR OF ALL FLIGHT CONTROL SURFACES. TRAILING EDGE FLAP, AILERON, SPOILER, RUDDER AND ELEVATOR CONTROL SURFACES ARE FULLY POWERED. ISOLATE ANY SYSTEM NOT INTENDED FOR OPERATION TO PREVENT INJURY TO PERSONNEL OR DAMAGE TO EQUIPMENT.
(b)
Provide systems 2, 3, and 4 hydraulic power (Ref 29-11-00/201).
(c)
Check that the control wheels are in neutral.
(d)
Place thrust levers 1 and 3 to thrust position of more than 10°.
(e)
Place speed brake control lever to ARM.
(f)
Move thrust levers 1 and 3 to thrust position of less than 6°. Speed brake control lever will automatically move aft to UP position, and all spoilers will extend to 45°.
NOTE: The position of spoilers 4 and 12 is displayed on the
____
the EICAS status page.
(g)
Move thrust levers 1 and 3 to thrust position of more than 10°. The speed brake control lever will automatically move forward to DN position, and all spoilers will fully retract.
(h)
Move thrust levers to thrust position of less than 6°.
(i)
Move reverse thrust levers 2 and 4 to deployed position. Speed brake control lever will automatically release from DN detent and will move to UP position. All spoilers will extend to 45°.
(j)
Move reverse thrust levers to stowed position.
(k)
Move speed brake control lever to DN. All spoilers will fully retract.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-62-00
ALL ú ú 03 Page 14 ú Jun 10/89
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
SPEED BRAKE CONTROL SYSTEM - MAINTENANCE PRACTICES
__________________________________________________
1. General_______
A. There are two tasks in this procedure. There is a task for the deactivation and a task for the reactivation of the automatic speed brake control system.
(1)
To deactivate the speed brake control system, you must open a circuit breaker.
(2)
To reactivate the speed brake control system you must close a circuit breaker.
TASK 27-62-00-042-004
2. Automatic Speed Brake System Deactivation_________________________________________
A. Access
(1)
Location Zone
221 Control Cabin
B.
Procedure
S 862-001
WARNING: OPEN THE CIRCUIT BREAKERS TO PREVENT THE SPOILER RETRACTION.
_______ IF YOU USE THE SPEED BRAKE CONTROL LEVER TO LIFT THE SPOILERS, AND IF YOU RELEASE THE PRESSURE IN HYDRAULIC SYSTEMS NO. 1 AND 4, THE SPOILERS WILL RETRACT AUTOMATICALLY. THIS CAN CAUSE INJURY TO PERSONS.
(1)
Open these circuit breakers and attach DO-NOT-CLOSE tags:
(a)
P7, Overhead Circuit Breaker Panel
1) 7G6, SPEED BRAKE AUTO CONT
TASK 27-62-00-442-005
3. Automatic Speed Brake System Reactivation_________________________________________
A. Access
(1)
Location Zone
221 Control Cabin
B.
Procedure
S 862-003
WARNING: MAKE SURE THAT PERSONS AND EQUIPMENT ARE CLEAR OF THE SPOILERS
_______ BEFORE YOU CLOSE THE CIRCUIT BREAKERS. THE SPOILERS WILL AUTOMATICALLY RETRACT IF YOU RELEASE THE PRESSURE IN HYDRAULIC SYSTEMS NO. 1 AND 4. THIS CAN CAUSE INJURY TO PERSONS.
(1)
Remove the DO-NOT-CLOSE tags and close these circuit breakers:
(a)
P7, Overhead Circuit Breaker Panel
1) 7G6, SPEED BRAKE AUTO CONT
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú 中國航空網 m.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：747-400 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 6(106)
