FWD
TURNBUCKLE
STABILIZER TRIM CHAIN ASSEMBLY
SPROCKET OF THE FORWARD TRIM MECHANISM
CHAIN DEFLECTION FORCE POINT
PIN A
LINK
CONNECTOR LINK
B

Stabilizer Trim Chain Assembly Adjustment
Figure 402

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. AIRPLANES WITH NON-REINFORCED CONTROL ú

 76-11-02
 STANDS  ú CONFIG 1 ú C01 Page 404 ú Mar 15/92
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
1. RIGHT CONTROL
 SHAFT NUT  2. SHAFT FOR THE 
STABILIZER TRIM 
CONTROL WHEEL 
3. FRAME OF THE 
16. HORN RIGHT CONTROL 
CUTOUT  STAND 
SWITCH
15. FIRE 4. KEY  5. TOP RIGHT 
CONTROL  SIDE DOOR
 MODULE
6. TRIM CONTROL 
WHEEL OF THE 
RIGHT STABILIZER 

7. TIE ROD NUT (2 LOCATIONS)
14. CUTOUT SWITCHES FOR THE STABILIZER TRIM
13. BOLT
12. STABILIZER TRIM INDICATOR LINK
11. RIGHT CONTROL SHAFT
9. BOTTOM RIGHT  8. TIE ROD FOR THE ACCESS PANEL
STABILIZER TRIM FWDCONTROL WHEEL
CONTROL STAND
Control Stand Access Installation Figure 403
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. AIRPLANES WITH NON-REINFORCED CONTROL ú

 76-11-02
 STANDS  ú CONFIG 1 ú C01 Page 405 ú Mar 15/92
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
(b)  
Pull the tie rod (8) from the right side of the spline shaft.

 (c)  
Remove the right control wheel (6) from the spline shaft.

 (d)  
Remove the left and right top side doors (5).

 (e)  
Remove the bottom right access panel (9).

 (f)  
Disconnect the stabilizer trim cutout switches (14).

 (g)  
Cut the lockwire at the nut on the right control shaft (1). 1) Remove the nut (1).

 (h)  
Remove the engine and APU fire control module (15) from the aft electronic panel (AMM 26-21-51/401).

 (i)  
Remove the forward and aft cover tie straps (4 and 2, Fig. 404).

 (j)  
Remove the forward and aft cover angles (6 and 8, Fig. 404).

 (k)  
Remove the horn cutout switch (16, Fig. 403).

 (l)  
Remove the cover assemblies (5, Fig. 404) from the control stand.

 (m)  
Remove the frame (3, Fig. 403) from the right control stand.

 (n)  
Remove the key (4) from the slot in the right control shaft (12).

 (o)  
Install the control shaft nut (1) on the right control shaft (11) so that the spacer, stabilizer trim indicator, spacer and flap handle can be removed as a unit.

 (p)  
Remove the bolt (13) and remove the indicator link (12) from the stabilizer trim indicator.

 (q)  
Remove the right control shaft (11) with the nut, spacer, trim indicator, spacer, and flap handle as a unit.

 (r)  
Turn the left stabilizer trim wheel until you can get access to the connector link (10) in the stabilizer trim chain.

 (s)  
Remove the connector link and remove the chain from the sprocket. 1) Safety the chain in the bottom of the control stand with a

 wire.

 (t)  
Remove the trim control wheel for the left stabilizer (1, Fig. 404) from the spline shaft (7).

 (u)  
Remove the spline shaft (7) from the left side and the sprocket from the right side of the control stand.

 (v)  
Cut the lockwire at the nut (3) on the left control shaft. 1) Remove the nut (3).

 (w)  
Remove the left bottom access panel.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. AIRPLANES WITH NON-REINFORCED CONTROL ú
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 發動機控制 ENGINE CONTROLS(38)