曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
(m) Put the flap lever detent in the correct position for
 installation.
 (n) Install the four screws into the flap lever detent and the flap
 lever cover.
 (o) Tighten the four screws.
 S 434-071-C03
 (4)  Install the right stabilizer trim lever covers and the lightplates:
 (a) Remove the right stabilizer trim lever cover and the lightplate
 restraint.
 (b) Put the right stabilizer trim lever cover and the lightplate in
 the correct position for installation.
 (c) Install the electrical cable clamps.
 (d) Install the two screws into the right stabilizer trim lever
 cover and the lightplate.
 (e) Tighten the two screws.
 S 434-072-C03
 (5)  Install the thrust lever covers and seals:
 (a) Put the two right thrust lever covers and seals in their
 position for installation.
 (b) Install the three screws into each thrust lever cover and seal.
 (c) Tighten the six screws.
 S 434-073-C03
 (6)  Install the forward thrust lever stop:
 (a) Put the forward thrust lever stop in its position for
 installation.
 (b) Install the four screws into the forward thrust lever stop.
 (c) Tighten the four screws.
 S 434-074-C03
 (7)  Install the aft thrust lever stop:
 (a) Put the aft thrust lever stop in its position for installation.
 1) Make sure the tabs on the aft stop are pointing aft and
 down.
 (b) Install the three screws into the aft thrust lever stop.
 (c) Tighten the three screws.
 S 434-075-C03
 (8)  Install the aft guard plate:
 (a) Put the aft guard plate in its position for installation.
 (b) Install the two screws into the aft guard plate.
 (c) Tighten the two screws.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. AIRPLANES WITH EFIS-REINFORCED CONTROL ú
 76-11-01 STANDS WITH A STABLIZER TRIM SHAFT WITH ú CONFIG 3 A SELF-LOCKING INSERT-AND-BOLT ú C01 Page 423
 ú Mar 12/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
S 434-076-C03
 (9)  Install the stabilizer trim control wheels:
 (a)  
Install the left stabilizer trim control wheel in the correct position on the spline shaft.

 (b)  
Install the right stabilizer trim control wheel on the splined shaft.

 NOTE: Handles on the stabilizer trim control wheels must
____ be 90 (|15) degrees apart when installed on the control stand.
 (c)  Install the bolts.
 1)  Tighten the bolts to 150-170 inch-pounds (16.9-19.2 newton-meters).
 TASK 76-11-01-844-077-C03
 5.  Put the Airplane to its Usual Condition
_______________________________________
 A.  References
 (1)  
AMM 27-41-00/501, Horizontal Stabilizer Trim Control System

 (2)  
AMM 27-51-00/501, Trailing Edge Flap System

 (3)  
AMM 29-15-00/201, Hydraulic Systems A, B, and Standby

 (4)  
AMM 76-11-00/501, Engine Control System

 B.  Access
 (1)  Location Zones
 101 Control Cabin - Left
 102 Control Cabin - Right
 202 Lower Nose Compartment
 205 Electronic Compartment

 C.  Procedure
 S 864-078-C03
 (1)  
Make sure that the stabilizer trim indicator position agrees with the position of the stabilizer.

 (a)  If it is necessary, adjust the position of the indicator (AMM 27-41-00/501).

 (2)  
Connect the connector link in the stabilizer trim chain.

 S 824-080-C03

 (3)  
Adjust the stabilizer trim chain so that a 5-pound force will deflect the chain 0.25 +0.07/-0.07 inch at a point 4.5 +1.0/-1.0 inches above the forward tangent of the forward mechanism sprocket.

 S 864-079-C03
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. AIRPLANES WITH EFIS-REINFORCED CONTROL ú
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 發動機控制 ENGINE CONTROLS(35)