NOTE: Remove a stabilizer or the two elevators for access to the
____ tail cone. We recomend that you remove a stabilizer.
S 934-010-B00
(8) Make marks (or masking tape) on the fuselage to help install the tail cone in the same location.
E. Remove the Tail Cone
S 034-011-B00
(1)
Disconnect the wire bundle at the electrical connector which is installed on the bulkhead at body station 1156.
S 024-012-B00
(2)
Remove the tail cone.
(a) Remove the bolts and washers which attach the tail cone to the bulkhead.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
53-53-00
ALL ú ú B02 Page 402 ú Jul 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
(b) Remove the tail cone.
NOTE: It will be necessary to push the front end of the tail
____
cone together.
S 034-013-B00
(3)
If you will install a new tail cone, do this task: "Remove Elevator Index Plates" (Ref 27-31-81/401).
S 034-014-B00
(4)
If you will install a new tail cone, do this task: "Rudder Index Plate Removal/Installation - Existing Tail Cone" (Ref 27-31-81/401).
TASK 53-53-00-404-015-B00
3. Tail Cone Installation
______________________
A. Standard Tools and Equipment
(1) Protective Plastic Shield
B. Consumable Materials
(1) A00310 - Sealant, BMS 5-79
C. References
(1)
27-21-17/401, Rudder Index Plate
(2)
27-31-11/401, Elevator
(3)
27-31-81/401, Elevator Index Plate
(4)
27-41-11/401, Horizontal Stabilizer
(5)
49-81-11/401, Exhaust Duct Muffler
(6)
49-81-31/401, Aft Fairing Assembly
D. Access
(1)
Location Zone
704 Tail Cone
(2)
Access Panels
3801/3802 Tail Cone Access Doors
E. Install the Tail Cone.
S 864-016-B00
(1) Make sure these circuit breakers are open DO-NOT-CLOSE tags are installed:
(a) P18 Load Control Center Left
1) ACC COMP LITS
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
53-53-00
ALL ú ú B01 Page 403 ú Jul 15/94
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
2) NAV LT (if applicable)
S 424-017-B00
(2) Install the tail cone.
(a)
Apply the sealant, BMS 5-79, to the mating surfaces between the tailcone and fuselage.
(b)
Put the tail cone in its position on the bulkhead. 1) Make sure that the alignment marks are aligned.
(c)
Install the bolts and washers.
(d)
Remove the protective plastic shield.
S 434-018-B00
(3)
If you installed a new tail cone, do this task: "Rudder Index Plate Installation - New Tail Cone" (Ref 27-21-17/401).
S 434-019-B00
(4)
If you installed a new tail cone, do this task: "Install Elevator Index Plates" (Ref 27-31-81/401).
S 434-020-B00
(5)
Connect the wire bundle at the electrical connector installed on the bulkhead at station 1156.
F. Put the Airplane Back to Its Usual Condition
S 414-021-B00
(1)
Do this task to install the elevators if they were removed:
"Install Elevator" (Ref 27-31-11/401).
S 414-026-B00
(2)
Do this task to install the horizontal stabilizer if you removed one: "Horizontal Stabilizer Installation" (Ref 27-41-11/401).
