CAUTION:_______CAREFULLY REMOVE THE RDDMI FROM THE INSTRUMENT PANEL. TOO MUCH FORCE CAN CAUSE DAMAGE TO THE ELECTRICAL CABLE AT THE REAR OF THE RDDMI.
(c)
Carefully pull the RDDMI away from the instrument panel until you can get at the electrical connector.
CAUTION:_______DO NOT TOUCH THE CONNECTOR PINS ON THE RDDMI. IF YOU TOUCH THESE PINS, ELECTROSTATIC DISCHARGE FROM YOUR BODY CAN CAUSE DAMAGE TO THE RDDMI.
(d)
Disconnect the electrical connector from the RDDMI.
(e)
Install a dust cap on the electrical connector.
TASK 34-28-81-404-014
3. RDDMI Installation__________________
A. References
(1) AMM 24-22-00/201, Manual Control
B. Access
(1) Location Zones
101 Control Cabin - Left
102 Control Cabin - Right
C. Procedure
S 864-008
(1) Make sure these circuit breakers are open with DO-NOT-CLOSE tags attached:
(a)
P6 Circuit Breaker Panel
1) INSTRUMENT XFMR-2 (CAPT's RDDMI)
(b)
P18 Circuit Breaker Panel
1) INSTRUMENT XFMR-1 (F/O's RDDMI)
S 424-009
(2) Do these steps to install an RDDMI.
(a)
Remove the dust cap from the electrical connector.
(b)
Connect the electrical connector to the rear of the RDDMI.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
34-28-81
ALL ú ú 02 Page 402 ú Nov 15/96
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
CAUTION:_______ CAREFULLY INSTALL THE RDDMI INTO THE INSTRUMENT PANEL. TOO MUCH FORCE CAN CAUSE DAMAGE TO THE ELECTRICAL CABLE AT
THE REAR OF THE RDDMI.
(c) (d) Carefully install the RDDMI into the clamp at the rear of the instrument panel.Tighten the higher right screw and the lower left screw on the front of the RDDMI.
S 864-010
(3) Remove the DO-NOT-CLOSE tags and close these circuit breakers: (a) P6 Circuit Breaker Panel 1) INSTRUMENT XFMR-2 (CAPT's RDDMI) (b) P18 Circuit Breaker Panel 1) INSTRUMENT XFMR-1 (F/O's RDDMI)
S 864-011
(4) Supply electrical power (AMM 24-22-00/201).
S 764-012
ú (5) Make sure the panel lights on the RDDMI come on.
ú S 764-016
ú ú ú ú ú ú ú ú ú ú ú ú ú ú (6) Do these steps to do a test of the RDDMI.(a) Set the switches on the MSU to the ALIGN or NAV position.(b) Set the SYS DSPL switch on the ISDU to the L position.(c) Set and hold the DSPL SEL switch on the ISDU in the TESTposition.(d) After 10 seconds, make sure that these occur:1) The applicable RDDMI heading reads 15 degrees.(e) Release the DSPL SEL switch on the ISDU.(f) Set the SYS DSPL switch on ISDU to the R position.(g) Set and hold the DSPL SEL switch on the ISDU in the TESTposition.(h) After 10 seconds, make sure these occur:1) The applicable RDDMI heading reads 15 degrees.(i) Release the DSPL SEL switch on the ISDU.
S 864-013
(7) Remove electrical power if it is not necessary (AMM 24-22-00/201).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
34-28-81
ALL ú ú 02.1 Page 403 ú Jul 12/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
VERTICAL SPEED INDICATOR - REMOVAL/INSTALLATION
_______________________________________________
1. General_______
A. There are two tasks in this subject. The first task is for the removal of a vertical speed indicator (VSI). The second task is for the installation of a VSI.
B. Two VSIs are installed in the airplane. One VSI is installed on the captain's main instrument panel. The other VSI is installed on the first officer's main instrument panel.
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 導航 NAVIGATION 2(98)
