(b)  
Carefully remove the ISDU from the instrument panel until you can get at the electrical connectors.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 34-28-21

 ALL  ú ú 01 Page 401 ú Jul 15/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 (c)  
Disconnect the electrical connectors from the rear of the ISDU.

 (d)  
Identify the electrical connectors for the installation.

 TASK 34-28-21-404-004
 3.  ISDU Installation_________________
 A. References
 (1)  
AMM 20-40-12/201, Electrostatic Discharge Sensitive Devices

 (2)  
AMM 24-22-00/201, Manual Control

 B. Access
 (1)  Location Zones
 101 Control Cabin - Left

 C. Procedure
 S 864-005
 (1)  Make sure these circuit breakers are open with DO-NOT-CLOSE tags attached:
 (a)  
P6 Circuit Breaker Panel
 1) SECONDARY
 2) IRS NO. 2 AC
 3) IRS NO. 2 DC

 (b)  
P18 Circuit Breaker Panel
 1) IRS NO. 1 AC
 2) IRS NO. 1 DC

 S 424-006
 (2)  Install the ISDU (AMM 20-40-12/201).
 (a)  
Connect the electrical connectors to the ISDU.

 CAUTION:_______CAREFULLY INSTALL THE ISDU INTO THE INSTRUMENT PANEL. TOO MUCH FORCE CAN CAUSE DAMAGE TO THE ELECTRICAL CABLES AT THE REAR OF THE ISDU.

 (b)  
Carefully install the ISDU into the instrument panel.

 (c)  
Lock the fasteners on the front of the ISDU.

 S 864-007
 (3) Remove the DO-NOT-CLOSE tags and close these circuit breakers:
 (a)  P6 Circuit Breaker Panel
 1) SECONDARY

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 34-28-21

 ALL  ú ú 01 Page 402 ú Jul 15/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
 (b)  2) IRS NO. 2 AC 3) IRS NO. 2 DCP18 Circuit Breaker Panel 1) IRS NO. 1 AC 2) IRS NO. 1 DC
 (4)  S 864-008Supply electrical power (AMM 24-22-00/201).
 (5)  S 864-010Set the two switches on the IRS MSU to the NAV position.
 (6)  S 764-011Do a test of the ISDU as follows: (a) Set the SYS DSPL switch on the ISDU to the L (left) position. (b) Hold the DSPL SEL switch on the ISDU in the TEST position. (c) Make sure all the annunciators on the IRS MSU come on for approximately two seconds. (d) Release the DSPL SEL switch. (e) Set the SYS DSPL switch on the ISDU to the R (right) position. (f) Hold the DSPL SEL switch on the ISDU in the TEST position. (g) Make sure all the annunciators on the IRS MSU come on for approximately two seconds. (h) Release the DSPL SEL switch.
 (7)  S 864-014Set the two switches on the IRS MSU to the OFF position.
 (8)  S 864-015Remove electrical power if it is not necessary (AMM 24-22-00/201).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 34-28-21

 ALL  ú ú 01 Page 403 ú Jul 15/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 INERTIAL REFERENCE UNIT - REMOVAL/INSTALLATION
______________________________________________
 1.  General_______
 A.  There are two tasks in this subject. The first task is for the removal of an inertial reference unit (IRU). The second task is for the installation of an IRU.
 B.  Two IRUs are installed in the main equipment center. IRU-1 and IRU-2 are installed on shelf No. 5 in the electronic equipment rack E3.
 C.  See 20-40-12/201, Electrostatic Discharge Sensitive Devices for the correct procedure to remove/install an IRU.
 TASK 34-28-31-004-014
 2.  Inertial Reference Unit Removal_______________________________
　
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機(jī)維護(hù)手冊 導(dǎo)航 NAVIGATION 2(86)