(b)
Make sure the voltage at test pin K or test jack 10 is less than 2 volts dc.
(c)
Set the mode selector switch to AC MAN.
(d)
Set the toggle switch for the outflow valve to CLOSE and then to OPEN.
(e)
Make sure the voltage at test pin K or test jack 10 is less than 2 volts dc.
(f)
Set the mode selector switch to STBY.
(g)
Make sure the voltage at test pin K or test jack 10 is is 20 to 31 volts dc.
(h)
Set the mode selector switch to DC MAN.
(i)
Make sure the voltage at test pin K or test jack 10 is 20 to 31 volts dc.
S 725-024
(11) Do this test of the voltage (test pin L or test jack 11) of the DC actuator clutch:
(a)
Set the mode selector switch to AUTO and then to AC MAN.
(b)
Make sure the voltage at test pin L or test jack 11 is less than 2 volts dc.
(c)
Set the mode selector switch to STBY and then to DC MAN.
(d)
Make sure that the voltage at test pin L or test jack 11 is 20 to 31 volts DC.
S 725-025
(12) Do this test of the winding (test pin M or test jack 12) of the AC actuator motor:
(a)
Set the mode selector switch to AUTO.
(b)
Set the FLT-GRD switch to GRD.
(c)
Make sure the aft outflow valve is fully open.
(d)
Set the FLT-GRD switch to FLT.
NOTE: The outflow valve will close after 15 seconds.
____
(e)
Measure the AC voltage at test pin M or test jack 12 as the outflow valve closes.
(f)
Make sure the voltage at test pin M or test jack 12 is a minimum of 10 volts ac as the outflow valves moves from fully open to fully closed.
(g)
Set the mode selector switch to AC MAN.
(h)
Set the toggle switch for the outflow valve to OPEN.
(i)
Make sure the voltage at test pin M is 16 to 32 volts ac or at test jack 12 is less than 2 volts ac as the outflow valve opens.
(j)
Set the toggle switch for the outflow valve to CLOSE.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
21-31-00
ALL ú ú 01 Page 517 ú Jul 12/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
(k) Make sure the voltage at test pin M is less than 2 volts ac or at test jack 12 is 16 to 32 volts ac as the outflow valve closes.
S 725-026
(13) Do this test of the DC voltage (test pin P or test jack 14) of the standby system scheduling or the DC voltage (test pin R or test jack 15) of the automatic system scheduling:
CAUTION: SET THE VOLTMETER TO MEASURE DC VOLTAGE BEFORE YOU CONNECT
_______ THE VOLTMETER TO THE TEST PINS. YOU CAN CAUSE DAMAGE TO THE PRESSURE CONTROLLER IF YOU DO NOT OBEY.
(a)
Measure the DC voltage at test pin P or test jack 14.
(b)
Write the voltage measured at test pin P or test jack 14 to make sure you can subsequently refer to it.
(c)
Measure the voltage at test pin R or test jack 15.
(d)
Write the voltage measured at test pin R or test jack 15 to make sure you can subsequently refer to it.
NOTE: The difference between the voltages at test pins P
____ and R must be no more than 0.5 volt dc. The difference between the voltages at test jacks 14 and 15 must be no more than 0.5 volt dc.
TASK 21-31-00-725-027
4. Standby Rate Check
__________________
A. References
(1)
AMM 21-00-00/201, Air Conditioning
(2)
AMM 24-22-00/201, Electrical Power
B. Access
(1) Location Zone
101 Left Control Cabin
102 Right Control Cabin
C. Prepare for the test.
S 865-028
(1)
Supply electrical power (AMM 24-22-00/201).
S 865-029
(2) 中國航空網 m.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 空調 AIR CONDITIONING 1(93)
