(c)
MAN DC
(d)
STBY DC
(e)
AUTOMATIC DC
(f)
AUTOMATIC AC
(g)
MAN AC
(h)
STBY AC
(i)
All the circuit breakers on the CONTROL CABIN LIGHTING module
(j)
LANDING GEAR AIR/GND RELAY & LTS
S 862-051
(5) BEJ 061, 062, 101-112 WITHOUT SB 21-1118; Make sure these circuit breakers on the P18 panel are closed:
(a)
18A8, NO. 1 AIR DATA COMPUTER - 1 AC
(b)
18A9, NO. 1 AIR DATA COMPUTER - 1 (26VAC)
S 862-006
(6) Set the controls for the pressurization control system:
(a)
Set the mode selector to AUTO.
(b)
Set the FLT/GRD switch to GRD.
(c)
Set the CAB ALT selector to 500 feet above the field altitude.
(d)
Set the captain's standby altimeter to the barometric pressure of the field.
(e)
Set the CABIN RATE selector to the position with the triangle.
S 862-007
(7) Set the LIGHTS switch on the P2 panel to TEST and make sure these lights come on:
(a)
AUTO FAIL
(b)
OFF SCHED DESCENT
(c)
STANDBY
(d)
MANUAL
S 862-008
(8)
Set the LIGHTS switch on the P2 panel to BRT or DIM.
S 012-033
(9)
Remove the forward left lining in the forward cargo compartment.
D. Procedure
NOTE: On airplanes with the CPC 21 controller installed, let the
____ system operate for 15 minutes before you do the test. On airplanes with the CPC 22 controller installed, let the system operate for 5 minutes before you do the test.
S 862-009
(1) Make sure these lights on the P5 panel go off:
(a)
AUTO FAIL
(b)
OFF SCHED DESCENT
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
21-31-00
ALL ú ú 03 Page 202 ú Nov 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
(c)
STANDBY
(d)
MANUAL
S 932-035
CAUTION: KEEP HANDS AND TOOLS AWAY FROM THE OUTFLOW VALVE DURING THE
_______ TEST. THE OUTFLOW VALVE WILL MOVE, AND CAN CAUSE INJURY TO PERSONS.
(2)
Attach a KEEP CLEAR tag on or near the outflow valve.
S 862-010
(3)
Make sure the VALVE position indicator shows the aft outflow valve is open.
S 862-011
(4)
Visually make sure the forward outflow valve is open.
S 862-012
(5)
Set the FLT/GRD switch to FLT and make sure the VALVE position indicator shows the aft outflow valve closes.
NOTE: Approximately ten seconds after you set the FLT/GRD
____ switch to FLT, the VALVE position indicator shows movement.
S 862-013
(6)
Visually make sure that the forward outflow valve is closed.
S 862-014
(7)
Move the mode selector to CHECK and make sure these results occur:
(a)
AUTO FAIL light comes on
(b)
STANDBY light comes on
(c)
The outflow valve indicator shows the outflow valve opens
(d)
Visually make sure that the forward outflow valve opens.
(8)
Move the CAB ALT selector to 500 feet below the field level.
S 862-016
(9)
Make sure that the VALVE position indicator shows the aft outflow valve closes.
S 862-017
(10)
Move the FLT/GRD switch to GRD and make sure these results occur:
(a)
AUTO FAIL light goes off
(b)
STANDBY light goes off
(c)
The outflow valve indicator shows the outflow valve opens.
S 862-015
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 空調 AIR CONDITIONING 1(83)
