(a)
Place new coupling nut over ferrule on line A.
(b)
Place new retaining ring over ferrule to retain nut on Line A.
CAUTION: DISTORTING THE RING SHAPE MAY CAUSE PERMANENT DAMAGE TO THE RING AND MAY RESULT IN LEAKS AT THE FITTING.
(c)
Lubricate new O-ring with petrolatum and install O-ring on line B.
(d)
Line up A and B and firmly hand-tighten coupling nut.
CAUTION: DO NOT USE ANY TOOLS TO TIGHTEN FUEL LINE FITTINGS. DAMAGE TO FITTING COMPONENTS OR LOOSENING OF ADJACENT FITTINGS MAY OCCUR.
(e)
Lockwire nut to ferrule.
(2)
Install flexible half coupling if applicable (Fig. 403).
(a)
Place coupling nut over ferrule on line.
(b)
Place new retaining ring over ferrule to retain nut on line.
CAUTION: DISTORTING THE RING SHAPE MAY CAUSE PERMANENT DAMAGE TO THE RING AND MAY RESULT IN LEAKS AT THE FITTING.
(c)
Lubricate new O-ring with petrolatum and place over ferrule.
(d)
Place second new retaining ring over ferrule.
CAUTION: DISTORTING THE RING SHAPE MAY CAUSE PERMANENT DAMAGE TO THE RING AND MAY RESULT IN LEAKS AT THE FITTING.
(e)
Insert line into fitting and hand-tighten coupling nut.
(3)
Install flexible full coupling if applicable (Fig. 404).
(a)
Place coupling nut over ferrule on line A.
(b)
Place coupling over ferrule on line B.
(c)
Place one new retaining ring over each ferrule to retain nut and coupling on line ends.
CAUTION: DISTORTING THE RING SHAPE MAY CAUSE PERMANENT DAMAGE TO THE RING AND MAY RESULT IN LEAKS AT THE FITTING.
(d)
Lubricate new O-rings with petrolatum and place one O-ring over each ferrule.
(e)
Place the two tube ends together with a gap of 0.15 (+0.05) inch between the ferrules, so that the O-rings are sandwiched between the retainer rings and retainer halves. Snap the retainer halves together.
(f)
Hand-tighten coupling nut (See Fig. 404 for dimensional requirements). Lockwire coupling nut to coupling.
505
Jun 20/89 BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details. 28-22-141 Page 403
CAUTION: DO NOT USE ANY TOOLS TO TIGHTEN FUEL LINE FITTINGS. DAMAGE TO FITTING COMPONENTS OR LOOSENING OF ADJACENT FITTINGS MAY OCCUR.
D. Tighten fuel line clamps to support brackets with bolts, washers, and nut and tighten support brackets to structure with bolts, washers, and nuts if brackets are not riveted.
6. Restore Airplane to Normal
A. Clean mounting surfaces for bonding jumpers with solvent.
B. Install bolt, washer and nut connecting bonding jumpers and clamps.
C. Check bonding resistance between fuel line and structure per 20-22-01\I/C. Bonding resistance should not exceed 0.010 ohm.
D. If tank entry was made, check that all tools and equipment are removed from tank and install access panels (AMM 28-11-11/401, or AMM 28-11-31/401) as applicable.
E. Service fuel tanks (AMM 12-11-0).
F. Check replaced fuel line and/or fuel line coupling for leaks (AMM 28-22-0/201).
505
28-22-141 Page 404 BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details. Jun 20/89
505 Rigid Coupling Installation
Jun 20/89 Figure 402 28-22-141
Page 405
BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details.
Flexible Half Coupling Installation 505
28-22-141 Figure 403 Jun 20/89
Page 406
BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details.
505 Flexible Full Coupling Installation
Jun 20/89 Figure 404 (Sheet 1) 28-22-141
Page 407
BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details.
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737 AMM 飛機維護手冊 燃油 FUEL(143)
