(1KS1,1KS2) AMM 73-25-34-710-044 Read the Class 3 Faults AMM 79-33-15-000-041 Removal of the Oil Pressure Transmitter (4003EN) AMM 79-33-15-400-041 Installation of the Oil Pressure Transmitter (4003EN) AMM 79-34-15-000-041 Removal of the Low Oil Pressure Switch (4000EN) AMM 79-34-15-400-041 Installation of the Low Oil Pressure Switch (4000EN) ASM 79-36/01
3. Fault Confirmation
__________________
A. Test
(1) Do the operational test of the Engine Interface Unit (EIU) through the Centralized Fault Display System (CFDS) to read the Class 3 Faults (Ref. AMM TASK 73-25-34-710-044).
4. Fault Isolation
_______________
A. If the test gives the maintenance message OIL PRESS XMTR 2 4003EN OR LOW PRESS 2 SW 4000EN:
- replace the SW-LOW OIL PRESS(4000EN) (Ref. AMM TASK 79-34-15-000-041) and (Ref. AMM TASK 79-34-15-400-041).
(1) If the fault continues:
- replace the XMTR-OIL PRESS (4003EN) (Ref. AMM TASK 79-33-15-000-041) and (Ref. AMM TASK 79-33-15-400-041).
F 『 EEFF : ALL E ∞∞79-33-00∞∞∞∞∞∞∞∞∞∞Page 203
E E Feb 01/00 ERE ECES
E F 『 E C F M E E E E 56 E E E (2) If the fault continues:
- do a check of the wiring from the EIU 2 (1KS2) to the low oil pressure switch (4000EN) and the wiring from the EIU 2 (1KS2) to the oil pressure transmitter (4003EN) pins AA/8D, 8B to pins AA/3, 4 (Ref. ASM 79-36/01),
- repair or replace as required.
(3) If the fault continues:
- replace the EIU-2 (1KS2) (Ref. AMM TASK 73-25-34-000-040) and (Ref. AMM TASK 73-25-34-400-040).
B. Do the test given in Para. 3.A.
(1) No additional maintenance action is required if the fault is not confirmed.
(2) Repeat the fault isolation procedure if the fault continues.
F 『 EEFF : ALL E ∞∞79-33-00∞∞∞∞∞∞∞∞∞∞Page 204
E E Feb 01/00 ERE
ECES E
F 『
E C F M E
E E
E 56 E
E E
IDG OIL COOLING SYSTEM (REFER TO 24-21-00) - FAULT ISOLATION PROCEDURES
_______________________________________________________________________
TASK 79-40-00-810-801
R Engine 1 oil temperature read by the FADEC sensor is higher than 135 deg.C (275 deg.F)
1. Possible Causes
_______________
- IDG
- EIU
- fuel return valve
- IDG oil/fuel heat exchanger
- FADEC oil temperature sensor (not 4004EN)
- ECU (4000KS)
- pressure-holding valve (124QM)
- fuel recirculation check-valve
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
AMM 28-16-41-000-001 Removal of the Pressure-Holding Valve 124QM (125QM) AMM 28-16-41-400-001 Installation of the Pressure-Holding Valve 124QM
(125QM) AMM 28-16-42-000-001 Removal of the Fuel Recirculation Check-valve AMM 28-16-42-400-001 Installation of the Fuel Recirculation Check-valve AMM 71-00-00-710-006 Minimum Idle Check AMM 73-11-50-000-002 Removal of the Fuel Return Valve (FRV) AMM 73-11-50-210-002 Inspection/Check of the Fuel Return Valve AMM 73-11-50-400-002 Installation of the Fuel Return Valve AMM 73-21-60-000-001 Removal of the Electronic Control Unit (ECU) AMM 73-21-60-400-001 Installation of the Electronic Control Unit (ECU) AMM 79-21-10-210-002 Check of the Lubrication Unit Magnetic Plugs and
Screens AMM 79-21-20-000-002 Removal of the Main Oil/Fuel Heat Exchanger AMM 79-21-20-400-002 Installation of the Main Oil/Fuel Heat Exchanger AMM 79-31-40-000-002 Removal of the Oil Temperature Sensor (IDG Cooling
System Control Sensor)
AMM 79-31-40-400-002 Installation of the Oil Temperature Sensor (IDG
Cooling System Control Sensor)
3. Fault Confirmation
__________________
A. Test
(1) Not applicable.
F 『 EEFF : ALL E ∞∞79-40-00∞∞∞∞∞∞∞∞∞∞Page 201
E E Nov 01/99 E E ECES
E
F 『
E C F M E
E E
E 56 E
E E
4. Fault Isolation
_______________
R A. Check the log book/crew report and Post Flight Report (PFR) for IDG
R failure warning or message. This failure is triggered if the engine oil temperature goes beyond 135 deg.C (275 deg.F) possibly caused by too high IDG oil temperature.
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 OIL 滑油(29)
