R (2) If the test does not give the maintenance message EOT SENS, J13, ECU:
R - do a check of the connectors on the harness HJ13 between the ECU
R and the oil temperature sensor for absence of loosening,
R contamination, corrosion or damaged pins or sockets,
R - clean, retighten or replace the harness HJ13 as required (Ref. AMM

 TASK 73-21-50-210-001).
R (a) If nothing is found:
R - replace the oil temperature sensor (Ref. AMM TASK 79-31-40-000-R 001) and (Ref. AMM TASK 79-31-40-400-001).

R 1_ If the fault continues:
R - replace the harness HJ13 (Ref. AMM TASK 73-21-50-000-046)
R and (Ref. AMM TASK 73-21-50-400-046).

R a_ If the fault continues:
R - replace the ECU (4000KS) (Ref. AMM TASK 73-21-60-000-001)
R and (Ref. AMM TASK 73-21-60-400-001).
R

 F 『 EEFF : ALL E ∞∞79-31-00∞∞∞∞∞∞∞∞∞∞Page 208
 E E May 01/00 E E ECES
E F 『 EEFF : ALL E ∞∞79-31-00∞∞∞∞∞∞∞∞∞∞Page 209

 F  『
 E  C F M  E
 E  E
 E  56  E
 E  E 

R  B. Do the test given in Para. 3. 
R  (1) No additional maintenance action is required if the fault is not 
R  confirmed. 
R  (2) Repeat the fault isolation procedure if the fault continues. 
R

 E E Feb 01/00 E E ECES
E

 F 『
 E C F M E
 E E
 E 56 E
 E E

 TASK 79-31-00-810-818
R Loss of the Signal of the FADEC Oil Temperature Sensor to the ECU on Engine 2 R Channel B
 1. Possible Causes
_______________
R - oil temperature sensor R - harness HJ13
 - ECU (4000KS)
 2. Job Set-up Information
______________________
 A. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
R R  AMM AMM AMM AMM AMM  73-21-50-000-046 73-21-50-210-001 73-21-50-400-046 73-21-60-000-001 73-21-60-400-001 
AMM  73-29-00-710-040 
AMM  79-31-40-000-001 
AMM  79-31-40-400-001 
ASM  73-25/18

 3. Fault Confirmation
__________________
Removal of the HJ13 HarnessVisual Inspection of the Wiring Harness Installation of the HJ13 HarnessRemoval of the Electronic Control Unit (ECU)(4000KS)Installation of the Electronic Control Unit (ECU)(4000KS)Operational Test of the FADEC on the Ground (with Engine non Motoring)Removal Oil Temperature Sensor (IDG Cooling System Control Sensor)Installation Oil Temperature Sensor (IDG Cooling System Control Sensor)
 A. Do the operational test of the FADEC 2B on the ground (with engine non motoring) (Ref. AMM TASK 73-29-00-710-040).
 4. Fault Isolation
_______________
R A. This fault message is generated if the output signal is lost from the ECU R dedicated oil temperature sensor used for the fuel return valve control.
R NOTE : This sensor is not used for the oil temperature indication in the
____ R cockpit.
R (1) If the test gives the maintenance message EOT SNSR, J13, ECU:
R - disconnect the connector of the harness HJ13 from the oil
R temperature sensor and do a resistance check of the sensor (Ref.
R ASM 73-25/18) between:

R . pins 1 and 2 (0.5 to 10 ohms)
 F 『

 ∞∞79-31-00∞∞∞∞∞∞∞∞∞∞Page 210
EEFF :  ALL  E 
E  E  May 01/00
 E  E
 ECES  E

 F  『
 E  C F M  E
 E  E
 E  56  E
 E  E 

R . pins 3 and 4 (0.5 to 10 ohms)

R . pins 2 and 5 (>1 megohm)

R . pins 3 and 5 (>1 megohm)

R . pin 1 and the ground (>1 megohm)

R . pin 4 and the ground (>1 megohm).

R (a) If the resistance values are out of the specified limits:
R - replace the oil temperature sensor (Ref. AMM TASK 79-31-40-000-R 001) and (Ref. AMM TASK 79-31-40-400-001).

R (b) If the resistance values are in the specified limits:
R - connect the harness HJ13 to the oil temperature sensor again,
R - disconnect the connector of the harness HJ13 from the ECU
R (4000KS) and do a resistance check (Ref. ASM 73-25/18) between:

R . pins 10 and 22 (0.5 to 10 ohms)

R . pins 9 and 20 (0.5 to 10 ohms)