(1KS1,1KS2) AMM 79-21-10-000-004 Removal of the Lubrication Unit AMM 79-21-10-400-004 Installation of the Lubrication Unit AMM 79-31-15-000-041 Removal of the oil Quantity Transmitter (4002EN) AMM 79-31-15-400-041 Installation of the Oil Quantity Transmiter (4002EN) ASM 79-36/01
3. Fault Confirmation
__________________
A. Test
(1) Make sure that the oil tank level confirms the oil indication on the lower ECAM display unit.
4. Fault Isolation
_______________
A. If the oil tank level confirms the oil indication:
R NOTE : Refer to CFM SB 79-021 covering HTS Oil coking issues. Trend
____ R instructions to monitor oil pressure trend and implement R Inspection and Cleaning procedures if necessary.
F 『 EEFF : ALL E ∞∞79-00-00∞∞∞∞∞∞∞∞∞∞Page 221
E E Feb 01/04 E E ECES
E
F 『
E C F M E
E E
E 56 E
E E
(1) Do a minimum idle check to make sure there are no leaks (Ref. AMM TASK 71-00-00-710-006).
(2) Do a check of the magnetic chip detector for abnormal debris .
(3) Do a check of the oil tank, lubrication unit, external oil supply and scavenge lines, for cracks/leaks.
(4) Do a check for heavy oil discharge in the center vent tube.
(a) If confirmed:
- replace the ENGINE-2 (1000EM2) (Ref. AMM TASK 71-00-00-000-042) and (Ref. AMM TASK 71-00-00-400-042).
(5) Do a check to see if the flame arrestor is clogged.
(a) If confirmed:
- clean or replace it.
(6) Remove TGB/AGB drain plug and do a check for abnormal oil quantity. If greater than one quart:
- do a check for blockage of the oil scavenge line or replace the lubrication unit (Ref. AMM TASK 79-21-10-000-004) and (Ref. AMM TASK 79-21-10-400-004).
(7) Do a borescope inspection of the high pressure compressor stage 1 and 2 to see if they are covered with oil (Ref. AMM TASK 72-31-00-290-002).
(8) Do an inspection of the fan blades and booster stage 1 at 6 o'clock to see if they are covered with oil.
(9) Do an inspection of the frame struts and aft side of stage 4 low pressure blades to see if they are covered with oil.
(a) If there is oil:
- replace the ENGINE-2 (1000EM2) (Ref. AMM TASK 71-00-00-000-042) and (Ref. AMM TASK 71-00-00-400-042).
B. If the oil tank level does not confirm the oil quantity:
- replace the XTMR-OIL QTY (4002EN) (Ref. AMM TASK 79-31-15-000-041) and (Ref. AMM TASK 79-31-15-400-041).
(1) If the fault continues:
- do a check and repair the wiring from the oil quantity transmitter (4002EN) to the SDAC-1 (1WV1), SDAC-2 (1WV2) and EIU2 (1KS2).
F 『 EEFF : ALL E ∞∞79-00-00∞∞∞∞∞∞∞∞∞∞Page 222
E E Feb 01/04 ERE ECES
E
F 『
E C F M E
E E
E 56 E
E E
C. If there are amber XX at the oil quantity indication location on the lower ECAM DU:
- do a check for 28VDC at the oil quantity transmitter (4002EN).
(1) If there is no 28VDC:
- do a check of the wiring between the circuit breaker (1EN2) and the oil quantity transmitter (4002EN) (Ref. ASM 79-36/01).
(2) If there is 28VDC:
- do a check and repair the wiring from the oil quantity transmitter (4002EN) to the EIU2 (1KS2) pins AA/3, 4 to pins AA/8F, 8H (Ref. ASM 79-36/01).
(a) If the fault continues:
- replace the EIU-2 (1KS2) (Ref. AMM TASK 73-25-34-000-040) and (Ref. AMM TASK 73-25-34-400-040).
D. Do a minimum idle check (Ref. AMM TASK 71-00-00-710-006).
F 『 EEFF : ALL E ∞∞79-00-00∞∞∞∞∞∞∞∞∞∞Page 223
E E Feb 01/00 ERE
ECES E
F 『
E C F M E
E E
E 56 E
E E
TASK 79-00-00-810-820
Oil Filter Clogged on Engine 1
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 OIL 滑油(12)
