R (19WV1,19WV2,21WV1,21WV2) AMM 52-71-13-400-001 Installation of the Proximity Switches R (19WV1,19WV2,21WV1,21WV2) AMM 52-73-21-000-003 Removal of the SLIDE ARMED Indicator-Light (2WN1, 2WN2) of the Emergency Exit AMM 52-73-21-400-003 Installation of the SLIDE ARMED Indicator-Light
(2WN1, 2WN2) of the Emergency Exit
ASM 31-54/00
ASM 31-54/05
ASM 52-73/01
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R EFF : 001-049, 051-099, 101-149, 151-199, ∞∞52-21-00∞∞∞∞∞∞∞∞∞∞Page 201
201-299, 401-499, Aug 01/05 CES
3. Fault Confirmation
__________________
A. Make sure that this(these) circuit breaker(s) is(are) closed:
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------121VU EIS/SLIDES/ARM AND WARN/FLT 15WN P11 121VU EIS/SLIDES/ARM AND WARN/GND 13WN P10
B. Test
(1) Do the EIS start procedure (Upper ECAM DU and lower ECAM DU only) (Ref. AMM TASK 31-60-00-860-001)
(2) Remove and install the cover flap of the LH-FWD emergency-exit hatch (referred to as the hatch) (Ref. AMM TASK 25-23-47-000-001) and (Ref. AMM TASK 25-23-47-400-001).
NOTE : This makes sure that the target bracket of the cover flap is
____ in its correct installation position.
(3) On the DOOR/OXY page of the lower ECAM DU, look for the possible fault indication.
4. Fault Isolation
_______________
A. When the cover flap is correctly installed and the DOOR/OXY page of the lower ECAM DU shows the symbol for the hatch and the message EMER EXIT in amber:
- make sure that the adjustment of the PROX SW-HANDLE FLAP, L FWD EMER EXIT (19WV1) is correct (Ref. AMM TASK 52-71-13-400-001).
(1) If the fault continues:
- installthe jumper wire between the: PROX SW-HANDLE FLAP, L FWD EMER EXIT (19WV1) connectors A/C and A/B (Ref. ASM 31-54/05).
(a) If the message EMER EXIT goes off and the symbol for the hatch changes to green:
- replace the PROX SW-HANDLE FLAP, L FWD EMER EXIT (19WV1) (Ref. AMM TASK 52-71-13-000-001) and (Ref. AMM TASK 52-71-13-400-001).
(b) If the message EMER EXIT remains on in amber:
- do a check for 28 VDC between the: PROX SW-HANDLE FLAP, L FWD EMER EXIT (19WV1) connectors A/A and A/C (Ref. ASM 31-54/05).
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R EFF : 001-049, 051-099, 101-149, 201-299, ∞∞52-21-00∞∞∞∞∞∞∞∞∞∞Page 202
May 01/05 CES (2) If the fault continues:
1_ If there is 28 VDC:
- do a check and repair the wiring between:
the PROX SW-HANDLE FLAP, L FWD EMER EXIT (19WV1) connector
A/B and the IND LT-SLIDE ARMED, L EMER EXIT (2WN1) connector
A/E (Ref. ASM 31-54/00).
2_ If there is no 28 VDC:
- do a check and repair the wiring between the:
PROX SW-HANDLE FLAP, L FWD EMER EXIT (19WV1) connector A/A
and the IND LT-SLIDE ARMED, L EMER EXIT (2WN1) connector A/R
(Ref. ASM 31-54/00).
PROX SW-HANDLE FLAP, L AFT EMER EXIT (21WV1) connector A/C
and ground (Ref. ASM 31-54/05).
- replace the IND LT-SLIDE ARMED, L EMER EXIT (2WN1) (Ref. AMM TASK 52-73-21-000-003) and (Ref. AMM TASK 52-73-21-400-003).
(a) If the fault continues:
- do a check and repair the wiring between: the IND LT-SLIDE ARMED, L EMER EXIT (2WN1) connector A/G and the SDAC-1 (1WV1) or SDAC-2 (1WV2) connector AA/11C (Ref. ASM 52-73/01) .
1 If the fault continues:
_ do the trouble shooting procedure of the SDAC-1 (1WV1) or SDAC-2 (1WV2) (Ref. TASK 31-54-00-810-803) or (Ref. TASK 31-54-00-810-810).
B. Test
(1) On the ECAM control panel:
- push the DOOR key to get the DOOR/OXY page.
(2) Make sure that the latch pin for both LH emergency exits is in the slide armed position.
(3) Make sure that the SLIDE indication is shown on the DOOR/OXY page.
NOTE : If this occurs, the trouble shooting procedure is correct.
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 艙門 DOORS(67)
