-------------------------------------------------------------------------------
REFERENCE DESIGNATION -------------------------------------------------------------------------------
R R R R R R  AMM AMM AMM AMM AMM ASM ASM AWM  52-73-21-000-002 52-73-21-000-003 52-73-21-400-001 52-73-21-400-002 52-73-21-400-003 31-54/0231-54/0552-73-07 Removal of the SLIDE ARMED Indicator-Light (3WN1, 3WN2) of the Aft Passenger/Crew Door Removal of the SLIDE ARMED Indicator-Light (2WN1, 2WN2) of the Emergency Exit Installation of the SLIDE ARMED Indicator-Light (1WN1, 1WN2) of the FWD Passenger/Crew DoorInstallation of the SLIDE ARMED Indicator-Light (3WN1, 3WN2) of the Aft Passenger/Crew Door Installation of the SLIDE ARMED Indicator-Light (2WN1, 2WN2) of the Emergency Exit
 3. Fault Confirmation__________________
 A. Job Set-up
 (1) Aircraft Maintenance Configuration
 (a) Energize the aircraft electrical circuits (Ref. AMM TASK 24-41-00-861-002).
 (b) Do the EIS start procedure (Upper ECAM DU and lower ECAM DU only) (Ref. AMM TASK 31-60-00-860-001).
 B. Make sure that this(these) circuit breaker(s) is(are) closed:
 -------------------------------------------------------------------------------
PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------
121VU EIS/SLIDES/ARM AND WARN/GND  13WN  P10
 C. Test
 (1) Make sure that the right after passenger/crew door is fully closed and the indicator plate shows LOCKED.
 (2) On the ECAM control panel: - push the DOOR key to get the DOOR/OXY page.
 (3) On the DOOR/OXY page: - make sure that the CABIN indication comes into view amber.

 4. Fault Isolation
_______________

R A. On the Door/Oxy page, if the CABIN indication comes into view amber:
R - do a check for 28VDC between pins A and D of the handle proximity
R switch (17WV2) (Ref. ASM 31-54/05).

R (1) If there is no 28VDC:
R - do a check for 28VDC at pin S of the indicator light (3WN2).

R (a) If there is 28VDC:
R - repair the wiring as necessary.

R  1_  If there is no 28VDC:
R  - do a check for 28VDC between pins A and U of the indicator 
R  light (3WN2). 

R a_ If there is 28VDC:
R - replace the IND LT-SLIDE ARMED, AFT R DOOR (3WN2) (Ref.
R AMM TASK 52-73-21-000-001) and (Ref. AMM TASK 52-73-21-R 400-001).

R b_ If there is no 28VDC:
R - do a check for 28VDC at pin B of the indicator light
R (2WN2).
R
R * If there is no 28VDC:
R - replace the IND LT-SLIDE ARMED, R EMER EXIT (2WN2) (Ref.
R AMM TASK 52-73-21-000-003) and (Ref. AMM TASK 52-73-21-R 400-003).
R
R * If there is 28VDC:
R - repair the wiring as necessary.
R

R (2) If there is 28VDC:
R - disconnect the connector of the handle proximity switch (17WV2)
R - install the jumper wire between pins B and C of the connector
R (17WV2-A) (Ref. ASM 31-54/05)
R - do the test given in Para. 3.C.

R (a) On the Door/Oxy page, if the CABIN indication comes into view
R green:
R - remove the jumper wire between pins B and C of the connector
R (17WV2-A)
R - connect the connector of the handle proximity switch (17WV2)
R - adjust the handle proximity switch (17WV2) with the door
R checking tool (Ref. AMM TASK 52-71-00-820-002) or with the ECAM
R system (Ref. AMM TASK 52-71-00-820-002).

R 1_ On the Door/Oxy page, if the CABIN indication comes into view
R amber:

 「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞52-13-00∞∞∞∞∞∞∞∞∞∞Page 217
 Nov 01/03 CES

R - replace the PROX SW-HANDLE, R AFT PAX/CREW DOOR (17WV2) R (Ref. AMM TASK 52-71-11-000-001) and (Ref. AMM TASK 52-71-11-400-001).
R (b) On the Door/Oxy page, if the CABIN indication comes into view
R amber:
R - remove the jumper wire between pins B and C of the connector
R (17WV2-A)
R - connect the connector of the handle proximity switch (17WV2)
R - do a check for 28VDC between pins A and D of the hook proximity
R switch (15WV2) (Ref. ASM 31-54/05).

R 1_ If there is no 28VDC:
R - repair the wiring as necessary.

R 2_ If there is 28VDC:
R - disconnect the connector of the hook proximity switch
R (15WV2)
R - install the jumper wire between pins B and C of the
R connector (15WV2-A) (Ref. ASM 31-54/05)
R - do the test given in Para. 3.C.

R a_ On the Door/Oxy page, if the CABIN indication comes into
R view green:
R - remove the jumper wire between pins B and C of the
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 艙門 DOORS(50)