曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

R connector (15WV2-A)
R - connect the connector of the hook proximity switch
R (15WV2)
R - adjust the hook proximity switch (15WV2) with the door
R checking tool (Ref. AMM TASK 52-71-00-820-001) or with
R the ECAM system (Ref. AMM TASK 52-71-00-820-001).
R
R * On the Door/Oxy page, if the CABIN indication comes
R into view amber:
R - replace the PROX SW-HOOK, R AFT PAX/CREW DOOR (15WV2)
R (Ref. AMM TASK 52-71-11-000-001) and (Ref. AMM TASK 52-
71-11-400-001).
R b_ On the Door/Oxy page, if the CABIN indication comes into
R view amber:
R - remove the jumper wire between pins B and C of the
R connector (15WV2-A)
R - connect the connector of the hook proximity switch
R (15WV2)
R - disconnect the plug 2878VC of the indicator light (3WN2)
R - install the jumper wire between pins F and G of the plug
R 2878VC (Ref. AWM 52-73-07)
R - do the test given in Para. 3.C.
R
R * On the Door/Oxy page, if the CABIN indication comes
R into view green:

 「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞52-13-00∞∞∞∞∞∞∞∞∞∞Page 218
 Nov 01/03 CES

R  - remove the jumper wire between pins F and G of the plug 
R  2878VC 
R  - replace the IND LT-SLIDE ARMED, AFT R DOOR (3WN2) (Ref. 
R  AMM TASK 52-73-21-000-002) and (Ref. AMM TASK 52-73-21-
400-002). 
R 
R  * On the Door/Oxy page, if the CABIN indication comes 
R  into view amber: 
R  - remove the jumper wire between pins F and G of the plug 
R  2878VC 
R  - connect the plug 2878VC to the indicator light (3WN2) 
R  - do a check for a ground signal at pin C of the handle 
R  proximity switch (17WV2) (Ref. ASM 31-54/05). 
R 
R  ** If there is no ground signal: 
R  - repair the wiring from the pin C of the handle proximity 
R  switch (17WV2) to the ground terminal (Ref. ASM 31-54/05) 
R 
R  ** If there is a ground signal: 
R  - do a check of the wiring between: 
R  *** the handle proximity switch (17WV2) pin B and the 
R  indicator light (3WN2) pin F, 
R  *** the indicator light (3WN2) pin G and the hook 
R  proximity switch (15WV2) pin C, 
R  *** the hook proximity switch (15WV2) pin B and the 
R  SDAC-1(2) pin AD/11H (Ref. ASM 31-54/02) and (Ref. ASM
 31-54/05). 
R  - repair the wiring as necessary. 
R  3_  If the fault continues:
R  - replace the SDAC-1 (1WV1) (Ref. AMM TASK 31-55-34-000-001) 
R  and (Ref. AMM TASK 31-55-34-400-001). 
R  4_  If the fault continues:
R  - replace the SDAC-2 (1WV2) (Ref. AMM TASK 31-55-34-000-001) 
R  and (Ref. AMM TASK 31-55-34-400-001). 
R
 B. Test

 (1) On the ECAM control panel:

 - push the DOOR key to get the DOOR/OXY page.

 (2) Make sure that the CABIN indication comes into view green on the ECAM system page.

 「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞52-13-00∞∞∞∞∞∞∞∞∞∞Page 219
 Nov 01/03 CES 5. Close-up

________
 A. Put the aircraft back to its initial configuration.
 (1) On the ECAM control panel, set the LOWER DISPLAY and the UPPER DISPLAY potentiometers to OFF.

 (2) De-energize the aircraft electrical circuits
 (Ref. AMM TASK 24-41-00-862-002).

 

 「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞52-13-00∞∞∞∞∞∞∞∞∞∞Page 220
 Nov 01/03R
 CES

 TASK 52-13-00-810-805

 No SLIDE Indication on the DOOR/OXY Page when the R Aft Escape Slide Handle is
 in the SLIDE ARMED Position
 1. Possible Causes
_______________
 - IND LT-SLIDE ARMED, AFT R DOOR (3WN2)

 - IND LT-SLIDE ARMED, R EMER EXIT (2WN2)

 - IND LT-SLIDE ARMED, FWD R DOOR (1WN2)

 - PROX SW-HANDLE, R AFT ESC SLIDE (7WN2)

 - RELAY-PWR SPLY SWITCHOVER (12WN)

 - wiring from the connector (7WN2-A) to the indicator light (3WN2)

 - wiring from the indicator light (3WN2) to the SDAC-1(2) (1WV1(2))
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 艙門 DOORS(51)