- do a check and repair of the aircraft wiring between ECB (59KD) AB/G8,G9 and IGV ACTUATOR (8014KM) P21/4,7 (Ref. ASM 49-61/02).
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R EFF : 001-049, 101-105, 107-107, 151-199, ∞∞49-00-81∞∞∞∞∞∞∞∞∞∞Page A264
201-210, Config-1 Aug 01/05 CES 1 If the fault continues:
_
- replace the ECB (59KD) (Ref. AMM TASK 49-61-34-000-003) and (Ref. AMM TASK 49-61-34-400-003).
B. If the APU GND SCANNING menu gives the maintenance message:
IGV ACTUATOR (8014KM)
associated with Fault Code Number (FCN) 110
- do a check for damage/contamination of electrical connector P21 of the IGV ACTUATOR (8014KM).
(1) If the electriacl connector P21 is damaged/contaminated:
- do a repair/cleaning.
(2) If the electrical connector is OK:
- use a multimeter to do a resistance check across pin 4 and pin 7 of the IGV ACTUATOR (P21), pin 4 and pin 10 of the IGV ACTUATOR (8014KM) connector P21
(a) If the resistance is
< 15 Ohms (pin 4-7)
or
< 100K Ohms (pin 4-10):
R - replace the IGV ACTUATOR (8014KM) (Ref. AMM TASK 49-23-51-000-R 004) and (Ref. AMM TASK 49-23-51-400-004).
(b) If the resistance is
> 15 Ohms and < 100 Ohms (pin 4-7)
and
> 100K Ohms (pin 4-10):
- do a check and repair of the aircraft wiring between ECB (59KD) AB/G8,G9 and IGV ACTUATOR (P21) P21/4,7 and/or IGV ACTUATOR (P21) P21/10 and aircraft GND (Ref. ASM 49-61/02).
1 If the fault continues:
_
- replace the ECB (59KD) (Ref. AMM TASK 49-61-34-000-003) and (Ref. AMM TASK 49-61-34-400-003).
R **ON A/C 001-049, 101-105, 107-107, 151-199, 201-210,
C. Do a check of the APU GND SCANNING menu to verify the fault is not present.
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R EFF : 001-049, 101-105, 107-107, 151-199, ∞∞49-00-81∞∞∞∞∞∞∞∞∞∞Page A265
201-210, Config-1 Aug 01/05 CES
TASK 49-00-81-810-852
Pressure-Transducer Fault or ECB internal Fault (131-9(A))
1. Possible Causes
_______________
- PRESS XDCR WIRING OPEN OR ECB INTERNAL FAILURE
- APU INLET PRESSURE TRANSDUCER (P22)
- TOTAL PRESSURE TRANSDUCER (P23)
- DELTA PRESSURE TRANSDUCER (P24)
- APU wiring harness
- aircraft wiring
- ECB (59KD)
- APU INLET PRESSURE TRANSDUCER (8048KM)
- TOTAL PRESSURE TRANSDUCER (8044KM)
- DELTA PRESSURE TRANSDUCER (8043KM)
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific multimeter
B. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
AMM 49-51-16-000-002 Removal of the Transducer - Differential Pressure (8043KM) (131-9(A)) AMM 49-51-16-400-002 Installation of the Transducer - Differential Pressure (8043KM) (131-9(A)) AMM 49-51-17-000-002 Removal of the Transducer - Total Pressure (8044KM) (131-9(A)) AMM 49-51-17-400-002 Installation of the Transducer - Total Pressure
(8044KM) (131-9(A))
AMM 49-51-21-000-001 Removal of the Transducer - APU Inlet Pressure
(8048KM) (131-9(A))
AMM 49-51-21-400-001 Installation of the Transducer - APU Inlet Pressure (8048KM) (131-9(A)) AMM 49-61-34-000-003 Removal of the Electronic Control Box (ECB) (131-9(A)) AMM 49-61-34-400-003 Installation of the Electronic Control Box (ECB) (131-9(A)) ASM 49-61/01
3. Fault Confirmation
__________________
A. Read-out of ECB Trouble-Shooting Data
(1) Put the APU MASTER SW to the ON position.
(2) Get access to the APU LAST LEG/PREVIOUS LEG report.
(3) Push the '>' adjacent to the related CFDS failure message:
- the MCDU menu shows PRESS XDCR WIRING OPEN OR ECB INTERNAL FAILURE
(4) Get access to the APU GND SCANNING menu.
4. Fault Isolation
_______________
R **ON A/C 001-049, 101-105, 107-107, 151-154, 201-207,
A. If the APU GND SCANNING menu gives the maintenance message:
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 機載輔助動力 2(97)
