associated with Fault Code Numbers (FCN) 105, 106, 107, 108 or 125
- do a check for damage/contamination of electrical connector P19 of the FUEL CONTROL UNIT (8022KM)
(1) If the electrical connector P19 is damaged/contaminated:
- do a repair/cleaning.
(2) If the electrical connector is OK:
- use a multimeter to do a resistance check across pin 6 and pin 7 pin 8 and pin 9 of the FUEL CONTROL UNIT (8022KM)
(a) If the resistance value is not between 20 Ohms and 100 Ohms (pin 6 - 7) and/or not between 10 Ohms and 80 Ohms (pin 8 - 9).
- replace the FUEL CONTROL UNIT (8022KM) (Ref. AMM TASK 49-32-11-000-003) and (Ref. AMM TASK 49-32-11-400-003).
(b) If the resistance values are in the specified limits:
- do a check and repair of the aircraft wiring from the ECB (59KD) AB/H11,G7,F6 to the FUEL CONTROL UNIT (8022KM) P19/6,7,8 and the FUEL CONTROL UNIT (8022KM) P19/9 and GND (Ref. ASM 49-61/02).
1 If the fault continues:
_
- replace the ECB (59KD) (Ref. AMM TASK 49-61-34-000-003) and (Ref. AMM TASK 49-61-34-400-003).
R **ON A/C 001-049, 101-105, 107-107, 151-199, 201-210,
B. Do the test given in para. 3.
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R EFF : 001-049, 101-105, 107-107, 151-199, ∞∞49-00-81∞∞∞∞∞∞∞∞∞∞Page 264
201-210, Config-1 Aug 01/05 CES TASK 49-00-81-810-824
APU AUTO SHUTDWON - NO FLAME, Fuel Flow disagrees with Command (131-9(A))
1. Possible Causes
_______________
- ELECTRONIC CONTROL BOX (59KD)
- FUEL FLOW DISAGREES WITH COMMAND
- damage/contamination of electrical connector P19
- FUEL CONTROL UNIT (P19)
- aircraft wiring
- Fuel Filter (8028KM)
- LUBE OIL MODULE (8080KM)
- FUEL CONTROL UNIT (8022KM)
- FUEL FILTER (8028KM)
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific multimeter
B. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
AMM 49-00-00-860-008 APU Start by External Power (131-9(A)) AMM 49-32-11-000-003 Removal of the Fuel Control Unit (FCU) (8022KM) (131-9(A)) AMM 49-32-11-400-003 Installation of the Fuel Control Unit (FCU) (8022KM)
(131-9(A)) AMM 49-32-41-920-001 Replacement of the Fuel Filter (8028KM) (131-9(A)) AMM 49-61-34-000-003 Removal of the Electronic Control Box (ECB)
(131-9(A)) AMM 49-61-34-400-003 Installation of the Electronic Control Box (ECB)
(131-9(A)) AMM 49-91-45-000-003 Removal of Oil Lube Module (8080KM) (131-9(A)) AMM 49-91-45-400-003 Installation of Oil Lube Module (8080KM) (131-9(A)) ASM 49-61/02
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R EFF : 001-049, 101-105, 107-107, 151-199, ∞∞49-00-81∞∞∞∞∞∞∞∞∞∞Page 265
201-210, Config-1 Aug 01/05 CES
3. Fault Confirmation
__________________
A. Read-out of ECB Trouble-Shooting Data
(1) Put the APU MASTER SW to the ON position.
(2) Get access to the APU SHUTDOWN report.
(3) Push the '>' adjacent to LRU DATA:
- the MCDU menu shows
FUEL FLOW DISAGREES WITH COMMAND
(4) Start the APU and apply Bleed Air for 20 seconds, minimum (Ref. AMM TASK 49-00-00-860-008).
4. Fault Isolation
_______________ R **ON A/C 001-049, 101-105, 107-107, 151-154, 201-207,
A. If an APU auto shutdown occurs during the APU operation and the APU SHUTDOWN report gives the maintenance message:
NO FLAME
FUEL CONTROL UNIT P19/APU FUEL SUPPLY
associated with Fault Code Number (FCN) 79
- do a check for damage/contamination of electrical connector P19 of the FUEL CONTROL UNIT (P19)
(1) If the electrical connector P19 is damaged/contaminated:
- do a repair/cleaning.
(2) If the electrical connector is OK:
- use a multimeter to do a resistance check across pin 6 and pin 7 of the FUEL CONTROL UNIT (P19).
(a) If the resistance is > 100 Ohms:
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 機載輔助動力 2(58)
