(2) Get access to the APU SHUTDOWN report.
(3) Push the '>' adjacent to LRU DATA:
- the MCDU menu shows FLOW DIVIDER SOLENOID SHOWS CIRCUIT FAILURE
(4) Start the APU and apply Bleed Air for 20 seconds, minimum (Ref. AMM TASK 49-00-00-860-008).
4. Fault Isolation
_______________
R **ON A/C 001-049, 101-105, 107-107, 151-154, 201-207,
A. If an APU auto shutdown occurs during the APU operation and the APU SHUTDOWN report gives the maintenance message:
NO ACCELERATION
FLOW DIVIDER SOL P13
associated with the Fault Code Number (FCN) 126
- do a check for damage/contamination of the electrical connector P13 of the FLOW-DIVIDER SOLENOID (P13)
(1) If the electrical connector P13 is damaged/contaminated:
- do a repair/cleaning.
(2) If the electrical connector P13 is OK:
- use a multimeter to do a resistance check across pin 1 and pin 2 and pin 1 and pin 3 of the FLOW-DIVIDER SOLENOID (P13).
(a) If the resistance value are not between 10 Ohms and 80 Ohms (pin 1 to pin 2) and/or < 100 kOhms (pin 1 to pin 3):
- replace the FLOW-DIVIDER SOLENOID (P13) (Ref. AMM TASK 49-32-13-000-001) and (Ref. AMM TASK 49-32-13-400-001).
(b) If the resistance values are in the specified limits:
- do a check and repair of the aircraft wiring from the ECB (59KD) AB/11 to the FLOW-DIVIDER SOLENOID (P13) P13/1 and the FLOW-DIVIDER SOLENOID (P13) P13/2 to GND (Ref. ASM 49-61/01).
1 If the fault continues:
_
- replace the ECB (59KD) (Ref. AMM TASK 49-61-34-000-003) and (Ref. AMM TASK 49-61-34-400-003).
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R EFF : 001-049, 101-105, 107-107, 151-199, ∞∞49-00-81∞∞∞∞∞∞∞∞∞∞Page A234
201-210, Config-1 Aug 01/05 CES
**ON A/C 001-049, 101-105, 151-199, 201-210,
Post SB 49-1062 For A/C 001-049,101-105,151-154,201-207,
A. If an APU auto shutdown occurs during the APU operation and the APU SHUTDOWN report gives the maintenance message:
NO ACCELERATION
FLOW DIVIDER SOL(8025KM)
associated with the Fault Code Number (FCN) 126
- do a check for damage/contamination of the electrical connector P13 of the FLOW-DIVIDER SOLENOID (8025KM)
(1) If the electrical connector P13 is damaged/contaminated:
- do a repair/cleaning.
(2) If the electrical connector P13 is OK:
- use a multimeter to do a resistance check across pin 1 and pin 2 and pin 1 and pin 3 of the FLOW-DIVIDER SOLENOID (8025KM)
(a) If the resistance value are not between 10 Ohms and 80 Ohms (pin 1 to pin 2) and/or < 100 kOhms (pin 1 to pin 3):
- replace the FLOW-DIVIDER SOLENOID (8025KM) (Ref. AMM TASK 49-32-13-000-001) and (Ref. AMM TASK 49-32-13-400-001).
(b) If the resistance values are in the specified limits:
- do a check and repair of the aircraft wiring from the ECB (59KD) AB/11 to the FLOW-DIVIDER SOLENOID (8025KM) P13/1 and the FLOW-DIVIDER SOLENOID (8025KM) P13/2 to GND (Ref. ASM 49-61/01).
1 If the fault continues:
_
- replace the ECB (59KD) (Ref. AMM TASK 49-61-34-000-003) and (Ref. AMM TASK 49-61-34-400-003).
R **ON A/C 001-049, 101-105, 107-107, 151-199, 201-210,
B. Do the test given in para. 3.
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R EFF : 001-049, 101-105, 107-107, 151-199, ∞∞49-00-81∞∞∞∞∞∞∞∞∞∞Page A235
201-210, Config-1 Aug 01/05 CES
TASK 49-00-81-810-842
APU AUTO SHUTDOWN - NO ACCELERATION, Oil Temperature Sensor out-of-range (high) (131-9(A))
1. Possible Causes
_______________
- OIL TEMP SENSOR SHOWS OUT OF RANGE HIGH
- damage/contamination of the electrical connector P11
- OIL TEMP SENSOR (P11)
- aircraft wiring
- ECB (59KD)
- Oil Sump Temp Sensor (8084KM)
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific multimeter
B. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 機載輔助動力 2(85)
