3. Job Set-up
__________
Subtask 77-00-00-861-050
A. Energize the aircraft electrical circuits (Ref. TASK 24-41-00-861-002).
Subtask 77-00-00-865-050
B. Make sure that this(these) circuit breaker(s) is(are) closed:
-------------------------------------------------------------------------------
PANEL DESIGNATION IDENT. LOCATION
-------------------------------------------------------------------------------
R **ON A/C 001-049, 051-099, 101-105, 151-199, 201-299, 301-302,
49VU EIS/PFD CAPT/SPLY 11WT1 E03
**ON A/C ALL
49VU EIS/ECAM/CTL/PNL 15WT E12 49VU EIS/DMC1/SPLY 10WT1 E11 49VU EIS/DMC3/STBY/SPLY 14WT1 E10 49VU EIS/DMC1/SWTG 21WT1 E09
F 『 EEFF : ALL E Page 50577-00-00
E E May 01/05 E E ECES E
F 『
E C F M E
E E
E 56-5B E
E E
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU EIS/DMC3/SWTG 21WT3 E07 49VU EIS/ECAM DU/UPPER/SWTG 24WT1 E06 49VU EIS/ECAM DU/UPPER/SPLY 13WT1 E05 49VU EIS/PFD CAPT/SWTG 22WT1 E04 49VU EIS/ND CAPT/SWTG 23WT1 E02 49VU EIS/ND CAPT/SPLY 12WT1 E01
R **ON A/C 106-149, 303-399, 401-499,
49VU EIS/PFD/CAPT/SPLY 11WT1 E03
**ON A/C ALL
121VU EIS/DMC3/SPLY 10WT3 Q09 121VU EIS/DMC2/SPLY 10WT2 Q08 121VU EIS/ECAM DU/LOWER/SPLY 13WT2 R11 121VU EIS/ECAM DU/LOWER/SWTG 24WT2 R10 121VU EIS/DMC2/SWTG 21WT2 R08 121VU EIS/ND/F/O/SWTG 23WT2 R06 121VU EIS/PFD/F/O/SWTG 22WT2 R05 121VU EIS/ND/F/O 12WT2 R04 121VU EIS/PFD/F/O 11WT2 R03
Subtask 77-00-00-860-051
C. Preparation before tests
(1) Do the EIS start procedure (Upper and Lower ECAM DUs only) (Ref. TASK 31-60-00-860-001).
(2) On the left or right MCDU get the SYSTEM REPORT TEST page (Ref. TASK 31-32-00-860-001).
F 『 EEFF : ALL E Page 50677-00-00
E E Aug 01/05 E E ECES E 4. Procedure
F 『
E C F M E
E E
E 56-5B E
E E
_________
(Ref. Fig. 501/TASK 77-00-00-991-300) Subtask 77-00-00-710-050
A. Do these tests:
-------------------------------------------------------------------------------ACTION RESULT -------------------------------------------------------------------------------
1. Push the line key adjacent to INST
2. Push the line key adjacent to DMC1
3. Push the line key adjacent to ENGINES
4. Push the line key adjacent to GENERAL RESET
5. Push the line key adjacent to RETURN until the INST menu comes into view.
6. Push the line key adjacent to DMC2
7. Push the line key adjacent to ENGINE
8. Push the line key adjacent to the GENERAL RESET
9. Push the line key adjacent to RETURN until the INST MENU comes into view.
F
EEFF : ALL
E
R E ECES The INST menu comes into view
- EIS (DMC1) page comes into view.
- On the PFD, ND CAPT side and upper ECAM display unit MAINTENANCE MODE comes into view.
- The MASTER CAUT light comes on.
- Ignore the ECAM warnings.
The EIS (DMC1) ENGINE OVER SPD/TEMPshows.
The over limit red indexes are reset.
The INST menu comes into view.
- EIS (DMC2) page shows.
- On the PFD, ND on F/O side and lower ECAM display unit MAINTENANCE MODE.
- The MASTER CAUT light comes on.
- Ignore the ECAM warnings.
The EIS (DMC2) ENGINE OVER SPD/TEMPshows.
The overlimit red indexes are reset.
The INST MENU comes into view.
『
E 77-00-00Page 507
E Feb 01/05
E
E
F 『
E C F M E
E E
E 56-5B E
E E
-------------------------------------------------------------------------------ACTION RESULT -------------------------------------------------------------------------------
10. On the center pedestal on the switching panel 8VU set the selector switch (EIS DMC) to CAPT 3 position.
11. Push the line key adjacent to DMC3
12. Push the line key adjacent to ENGINE
13. Push the line key adjacent to GENERAL RESET
14. Push the line key adjacent to RETURN until the CFDS MENU comes into view.
15. Stop the MCDU
16. On the center pedestal on the switching panel 8VU set the selector switch (EIS DMC) to NORM position.
5. Close-up
________
Subtask 77-00-00-860-050
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM ENGINE INDICATING 發動機指示(7)
