R  (6) Make sure that the lower extension lead (10) is not stressed and 
R  TORQUE as follows: 
R  (a) the connecting nut to between 168 and 186 lbf.in (1.89 and 2.10 
R  m.daN) and safety with lockwire 0.032 in (0.8 mm) dia (Material 
R  No. CP8001) or lockwire 0.032 in (0.8 mm) dia (Material No.
 CP8002). 
R  (b) the bolts (30), (80), (100), (130) and (150) to between 47 and 
R  531 lbf.in (0.53 and 6.00 m.daN).
 5. Close-up________ 
R
 Subtask 77-21-10-440-058 
R  A. Make the thrust reverser serviceable (Ref. TASK 78-30-00-081-041).
 Subtask 77-21-10-710-058 
R  B. Do an Operational Test of the FADEC Ground (with engine non motoring) 
R  (Ref. TASK 73-29-00-710-040).

 F 『 EEFF : ALL E Page 42177-21-10
 E E Aug 01/04 E E ECES E

 F 『
 E C F M E
 E E
 E 56-5B E
 E E
 Subtask 77-21-10-410-068

R C. Close Access R
R (1) Close the fan cowl doors (Ref. TASK 71-13-00-410-040): FOR 1000EM1
R  437AL, 438AR, FOR 1000EM2 447AL, 448AR.
R (2) Remove the warning notice(s).
 F 『 EEFF : ALL E Page 42277-21-10
 E E Aug 01/04 E E ECES E

R

R
R

R

F 『
 E C F M E
 E E
 E 56-5B E
 E E

 TASK 77-21-10-000-025
Removal of the Main Junction Box
 1. Reason for the Job
__________________
 Self Explanatory
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific blanking plugs No specific caps No specific warning notice
 B. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
71-13-00-010-040 Opening of the Fan Cowl Doors 78-30-00-481-041 Make the Thrust Reverser Unserviceable for
 Maintenance 78-36-00-010-040 Opening of the Thrust Reverser Doors 77-21-10-991-305 Fig. 403
 3. Job Set-up
__________
 Subtask 77-21-10-941-061
 A. Safety Precautions
 (1) On the center pedestal, on the ENG panel 115VU:

 (a) Put a warning notice to tell persons not to start the engine.

 (2) Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before you do this procedure.

 F 『 EEFF : ALL E Page 42377-21-10
 E E Aug 01/04 E E ECES E

 F 『
 E C F M E
 E E
 E 56-5B E
 E E
 (3) On the overhead maintenance panel 50VU:

 (a) Make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off.

 (b) Put a warning notice to tell persons not to energize the FADEC 1(2).

 Subtask 77-21-10-010-074
 B. Open the fan cowl doors: (Ref. TASK 71-13-00-010-040)
 FOR 1000EM1
 437AL, 438AR
 FOR 1000EM2
 447AL, 448AR

 Subtask 77-21-10-040-068
 C. Make the thrust reverser unserviceable (Ref. TASK 78-30-00-481-041).
 Subtask 77-21-10-010-084
 D. Open the thrust reverser doors: (Ref. TASK 78-36-00-010-040)
 FOR 1000EM1
 451AL, 452AR
 FOR 1000EM2
 461AL, 462AR

 4. Procedure
_________
R (Ref. Fig. 403/TASK 77-21-10-991-305)
 Subtask 77-21-10-020-063
R A. Removal of the Main Junction Box
R (1) Cut and remove the lockwires.
R (2) Disconnect the upper extension lead (10) and the lower extension lead R (40) from the main junction box (20).
R (3) Disconnect the CJ13 harness connector (60) from the main junction box R (20).
R (4) Disconnect the main junction box leads (20) from the upper left T495 R sector junction box (100) and lower left T495 sector junction box R (140).
 F 『 EEFF : ALL E Page 42477-21-10
 E E Aug 01/04 E E ECES E

 F 『
 E C F M E
 E E
 E 56-5B E
 E E
R (5) Remove the parts which attach the upper extension lead (10) as

R follows:
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM ENGINE INDICATING 發動機指示(20)